The 41-lb rectangular access door is held in the 90° open position by the single prop CD. Determine the magnitude of the force F in the prop and the magnitude of the force normal to the hinge axis AB in each of the small hinges A and B. Assume a 27 in., b-42 in., c-11 in., d-46 in.

Q: Compute the distance back to the channel "b"in mm. Fy = 250 MPa Using NSCP 2001, compute the axial…

A: ANSWER HAS DONE FOR THE FIRST 2 QUESTIONS 1. distance back to channel for 2 channels: Ix = Iy Iy =…

Q: inforcement for a balanced design. If so reinforced, determine the safe moment PROBLEM: a capacity…

A:

Q: st) Consider this floor layout. The anticipated loading on the floor is 65 lbs/ft2. What is the load…

A:

Q: Determine the following: (a) Equation of Elastic Curve, (b) slope and direction at the free end, (c)…

A: Given cantilever beam with loading condition and asked to Determine: (a) Equation of Elastic Curve,…

Q: Fabricated by welding a 12.7 mm by 100 mm cover plate to one of its flanges. The effective length is…

A: For A36 steelfy = 250MPaFor W21 x 201,(Iy)w = 226.7x106 mm4 ; Aw(area of w-section) = 38230 mm2To…

Q: Use the method f sections to find the force the member s BD,CD,and EC

A:

Q: Jsing LRFD and A-50 steel, determine the maximum oad Pu that the system below can carry. Assume…

A:

Q: Plate Girder Solve the following Problem For the plate girder shown, consider shear only, check the…

A: Solution Given Data Fy= 36 ksi Width of web= 16" The thickness of web= 1" Height of Flange= 48" The…

Q: For the Integrated Project (office building), design the Floor Girders in the gravity-only system,…

A:

Q: Determine the Vertical Deflection at the hinge E- 29x103 ksi = 80 in 4 5 k internal hinge 1.2I 3'

A:

Q: Calculate the quantity of steel required for stirrups for the following beam.

A: The stirrups the member of reinforcement which in the shape of closed loop of bar.  These bar hold…

Q: The equation of the three hinged symmetrical arch for the given coordinate is, when the arch perform…

A:

Q: Identify the twp-force members in this frame. 192 N 1.25 m C ID 3. 1.75 m 3. IE F -2 m 2 m Select…

A: A two force member consists of two hinges or pins at both ends and has no external load in between…

Q: D 32 ft d. 64k

A:

Q: A steel loop ABCD of length 5 ft and of -in. diameter is placed as shown around a 1-in.-diameter…

A:

Q: B 4 ft P D C 3 ft- 3 ft

A:

Q: 10 kN 6 kN/m 5 kN/m В 10 kN E 3 m 1.5 m--1.5 m--1.5 m-| CS CamScanner ile tarandı

A:

Q: Determine bar force members EB, EC, and DC using method of sections. Complete solution

A:

Q: The tension member is a PL 10x137 of A36 steel. It is connected to a 10mm thick gusset plate, also…

A:

Q: Q3) A simply supported beam has been sa distance d from the support face the follo V-45 KN, M-9KN.m…

A:

Q: Question 14 Beam A-B-C-D is a W360x79 with a modulus of elasticity of 200 000 MPa. It has hinge…

A:

Q: Check the adequacy of column AB for applied live load. Fy= 350M

A: fy = 350 MPaCompression member:W 360 x 51A = 6450 mm2 rx = 148 mmry = 38.8 mmd = 355 mmb = 171 mmt =…

Q: Pb4 The crane weighs 8 tons with center of gravity at G and is held in place by the pin connection…

A: Given :

Q: The plan shown below represents a floor system, where all columns have cross section dimensions of…

A: a) As per Table 9.5 (a) of ACI: 318-11,

Q: Draw the FBD All distributed loads should be simplified to their equivalent loads Draw the FBD…

A:

Q: F E B 3,2 KN 2.0r 2.0 m 8 KN A L5m 1.5m 1.5m 1.5 m

A:

Q: Q3: A cast-iron bracket has a cross section and subjected to loading shown; A) If the compressive…

A:

Q: For the system below, find the maximum stress for the member ECD due to combined effect of axial and…

A:

Q: A column section b- 400 mn, h- 600 mm is reinforced with longitudinal bars Ast - 12-020 mm equally…

A:

Q: The beam supports a distributed load with a maximum value of 40 lb/ft at A. Determine the resultant…

A: Value of distributed load = 40 lb/ft total span length= 15 ft

Q: W8 x 13 W8XI5 4m Pa

A:

Q: FUNDAMENTAL PROBLEMS V27 Resolve cach force acting on the post into its I and y components. F2-10.…

A: As per bartleby policy I can answer only one question at a time. please re-upload the remaining one.…

Q: Determine the effective slenderness ratio for the column for bending about the y centroidal axis.…

A: For section C 250×30, A=3790 mm2d=254 mmIx=Iz=32.8×106 mm4rx=rz=93 mmIy=1.17×106 mm4x=y=15.4 mm The…

Q: E,4A E,A E,2A L 2P L 8P 10P

A: Hello dear this is the solution of your problem The strain in each member is found to be…

Q: The force acting on the gear tooth is F-20 Ib. Resolve this force into two componeats acting along…

A: The resolution of F along aa is = F cos60…

Q: The structural system below using rotational spring + hinge support at joint A and rotational spring…

A: reestablishing force = applied second or force reestablishing force 'T1 = 2Kphi2 +Kphi1' applied…

Q: AW14X 53 structural steel [E = 29,000 ksi] section (see Appendix B for cross-sectional properties)…

A: Determine the maximum load P that may be supported by the column

Q: 1.) Draw the Free-Body Diagram for each mechanism shown. Provide a direction a a name for each…

A: To draw FBD

Q: Given a 9ft long column, which is fully Fixed in both directions at the bottom and is free to side…

A: Step 1:Step 2:Step 3: Step 4:

Q: A column in a building is shown in elevation below. Each floor level delivers 200 kips of force to…

A:

Q: 12-87. The W12 X 45 simply supported beam is made of A-36 steel and is subjected to the loading…

A: Given:Beam is made of W12X45, and A-36 steel To determine:Deflection at C

Q: Determine the angle θ between the edges of the sheet-metal bracket.

A: Consider two position vectors along the edge and right edge of the hinge Position vectors r1, r2 dot…

Q: 24 kN 3m -3m B 3 kN/m 4 m REDMI NOTE 9 PRO AI QUAD CAMERA

A: The following figure shows the Free Body Diagram of the frame.

Q: 2/58 The cantilevered W530 x 150 beam shown is subjec- ted to an 8-kN force F applied by means of a…

A: Given a cantilever beam W530×150 subject to a force of 8 kN. It is asked to determine the equivalent…

Q: bolt circle of radius 125mm. Determine lts if the shearing stress is limited to

A:

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.