The 3-in. I beam shown in the figure below has cross-sectional properties of A = 1.64 in.2, 111 = 2.0 in.4, and 122 = 0.46 in.4. It is made of steel having Sy = 42 ksi. Find the safe axial compressive load (in lb) based on a safety factor of 4 for pinned ends and unsupported length of 27.3 in. correct answers is 15,597.39 lb

The 3-in. I beam shown in the figure below has cross-sectional properties of A = 1.64 in.2, 111 = 2.0 in.4, and 122 = 0.46 in.4. It is made of steel having Sy = 42 ksi. Find the safe axial compressive load (in lb) based on a safety factor of 4 for pinned ends and unsupported length of 27.3 in. correct answers is 15,597.39 lb

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

AW 12 x 65 column section shown in the figure is pinned at each end and has an additional support in the weak direction at a point 4.1 m from the top. Use X- 4.8 m K 1 for both directions. X+Y Properties of W 12 x 65 A 12323 mm2 - 134.11 mm ry 76.71 mm Fy- 248 MPa Determine the allowable compressive strength (kN).
Please show your solution on a paper with FBD
write legibly Indicate all necessary FBDs, concepts and formulas needed in the solution. The members of the truss are 25mmx50mm in cross section. Determine the maximum load P that can be applied so that the stresses will not exceed 100 MPa in tension or 70 MPa in compression. See figure 101.
Given the truss as shown, solve the cross-sectional area of member BE if the stresses will not exceed 100MPa in tension or 80MPa in compression. Show all necessary solution.
Consider the truss shown in (Egure 1). Suppose that F-60 kN and F₂-25 kN Figure 40 KN Part C Fau 50 AN Submit -2m- D 15m 1of1 > 15m 15m μA Value -F₂ Part A Request Answer Determine the force in member ED of the truss, and state if the member is in tension or compression Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. HA FED Value Submit Part B Request A Determine the force in member EH of the truss, and state if the member is in tension or compression Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Submit Fon- Value Determine the force in member GH of the truss, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of…
Please answer the question correctly and pleaase put the answer on the paper. Thank you Note: The tolerance is ± 1 in the third significant digit. Put the exact answer
STRENGTH OF MATERIALS (SIMPLE STRAIN:Poisson’s Ratio: Biaxial and Triaxial Deformations)100% UPVOTE! PLEASE INCLUDE FBD IF NECESSARY. THANK YOU! GOD BLESS!
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 20 kips, w = 4.8 kips/ft, LAB = 4.2 ft, Lec = 4.2 ft, and Lco = 16.0 ft. Determine the magnitude of the maximum bending stress in the beam. P B C D LAB LBC LCD Answer: Omax = i ksi
Hello help me answer this. Thank you.
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 19 kips, w = 2.0 kips/ft, LAB = 3.4 ft, LBc = 3.4 ft, and LCD 15.6 ft. Determine the magnitude of the maximum bending stress in the beam. = P ksi Answer: Omax i B LAB LBC = C W LCD D X
Determine the force of the members for the space truss shown in the figure. Joints A and B are supported by ball-and-socket while Joint C is supported by short link along z-axis. Indicate whether member is tension (T) or compression (C). 2m y Sm Az By BX Bz PAR Ax CSXScanned with Ca canner a SISU KN 15m 1 2117
Please kindly give me a,b,c and d answers..help me. Urgent Thank you