The 20-kg steel ring A with inside and outside radii of 50 mm and 60 mm, respectively, rests on a fixed horizontal shaft of 40-mm radius. If a downward force P = 150 N applied to the periphery of the ring is just sufficient to cause the ring to slip, calculate %3D

Q: 1. According to the SAE viscosity classification, the oil (SAE oil (SAE 20) at the same temperature.…

A: we will discuss SAE viscosity ratings

Q: ength than A

A: introduction: here we find is the statement is false or true

Q: What functional problem results from torsion?

A: Given:What functional problem results from torsion?

Q: write an introduction for hardness test lab

A: Hardness Measurement methods.

Q: List four sources of engineering failures

A:

Q: This is a static mechanics question ( Detailed response needed) Question :  State and Describe The…

A:

Q: why bare pipe has 0% efficiency and full covered insulate pipe has more efficiency

A: A thermal insulator has a low thermal conductivity and is a poor heat conductor. To reduce heat loss…

Q: find the stress in the balt. BD Bearing at Gdoat mm 2OCM -2 Im 2.5m

A: Given Data The diameter of the bar is: dbat=16 mm The load acting at the end of the bolt is: P=10…

Q: Endurance Limit calculations are suited for types of loading Random Static Impact Repeated and…

A: Endurance limit is the maximum value of the fully  reversed bending stress which a material can…

Q: 02: Fully describe the gyroscopic effects on ships.

A: The front side of the ship is known as a bow and the rear end (the end where the rotor is present)…

Q: How does the element of material deforms?

A: elements of a material are deformed when some external force is applied to it.

Q: Customary units to SI units by using the values listed for length and force as defined values:…

A: Distributed load is equal to load(force) acting per unit length of any member.

Q: What type of force is commonly caused by electrostatic and gravitational force?

A: The force caused by the gravitation is always attractive force.

Q: 3.

A: For solution refer below images.

Q: True/false Q-5 Specific weight is an extensive property? If yes why ?

A: Specific weight is define as tge ratio of weight of the substance to its volume.  w• = W/v  W = mg {…

Q: _________ generally represents the total change in dimension experienced by the member. -elasticity…

A: To choose: The correct option. Concept used: Strain: An object or medium under stress becomes…

Q: Define and explain hookes law

A:

Q: A & D reactions? 6 kips/ft AB 9'-

A:

Q: Name the 2 types of axial loading?

A: Two types of axial loading are tensile and compressive stress. Both kinds of stresses arise within…

Q: Define eccentric impact.

A: Eccentric impact:- If the line of the impact of bodies doesn't coincide with the line connecting the…

Q: rank 20w-50, 5w- 30 and 10w-30 motor oils in terms of increasing viscosity ii)List three (3) ways…

A: i)20w-50, 5w- 30 and 10w-30 of these all motor , in terms of the inceasing viscosity 20w-50 is more…

Q: What is impingement velocity?

A: Flow impingement occurs when the approach channels flow directly into a bank line at large acute…

Q: 017 ABOUT INDUSTRIAL PIPING WHEN TO USE SPRING SUPPORTS WORKING UNDER COMPRESSION OR UNDER TRACTION?

A: The objective of the question is to understand when to use spring supports working under compression…

Q: Is it possible for an item to fail yield but not fail fatek

A: Given question : Is it possible for an item to fail by yielding but not fail by fatigue.   .

Q: 161 About industrial piping HOW ARE SIZING CALCULATIONS MADE FOR THE DEFINITION OF SPRING SUPPORTS?

A: The objective of this question is to understand how to perform sizing calculations for defining…

Q: Which of the following is/are TRUE? OEdge and screw dislocations lower the required shear stress for…

A: The reduction in area in low carbon steel is expressed as, Thus, a reduction in area is…

Q: 2015.2 2.4713 27 0.031 2182.4 3.4800 29.33 0.044 2416.9 4.9900 32.48 0.063 2693.1 7.5062 36.19 0.095…

A: Given Data  To find “Since you have posted a question with multiple sub-parts, we will solve the…

Q: Connecting rod bearings are to be replaced. The journal measures 70.866 mm (2.790 in.)​. The…

A: The Size bearings for above requirements are U/S--0.381 mm (0.015 in) undersize.

Q: Maximum Stresses in Thick Walled Cylinders

A: To determine the maximum radial and tangential stress for the thick walled cylinder

Q: ow many types of units are in SI? Choices a.3, b.4, c.1, d.2

A: NOTE: The correct answer is not coming to be in order with any of the options so kindly recheck the…

Q: 1. According to the SAE viscosity classification, the oil (SAE 40) is lower viscosity than the oil…

A: To decrease the friction losses in the bearing oil is used .varios types of the oils are used for…

Q: Calculate the volume (in ft) of material used in making 350 ft of 2 in. type L copper tubing.

A: Given that, From the table of type L copper tubeFor a 2 in. in nominal size tube:Outside diameter,…

Q: advantage and disadvantages of using STRAIN GAUGE

A: Given: Advantage and Disadvantages of using STRAIN GAUGE

Q: A calliper brake is required for the front wheels of a van with a braking capacity of 900 Nm for…

A: Given: The torque, T = 900 N.m The angle = 45 degrees The outer radius, R = 160 mm The inner radius,…

Q: discuss the principle of using elastic linear spring

A: Solution:

Q: Briefly disscus centrifugal seperation in hydro metallurgy

A: Centrifugation is a mechanical technique in which the centrifugal force is used to remove…

Q: Briefly define the purpose, types and construction of the hardness measurement.

A: The principal purpose of the hardness measurement  is to determine the suitability of a material for…

Q: Write a a short note on eccentric impact.

A: