The 184-lb exerciser is beginning to execute a bicep curl. When in the position shown with his right elbow fixed, he causes the 18-lb cylinder to accelerate upward at the rate 0.20g. Neglect the effects of the mass of his lower arm and estimate the normal reaction forces at A and B. Friction is sufficient to prevent slipping. A Part 1 B 10" 10" 13" Find the tension T in the rope. Answer: T = i 23° 65" lb 18 lb

The 184-lb exerciser is beginning to execute a bicep curl. When in the position shown with his right elbow fixed, he causes the 18-lb cylinder to accelerate upward at the rate 0.20g. Neglect the effects of the mass of his lower arm and estimate the normal reaction forces at A and B. Friction is sufficient to prevent slipping. A Part 1 B 10" 10" 13" Find the tension T in the rope. Answer: T = i 23° 65" lb 18 lb

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

H3
Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please
A train consists of a 479,000-lb locomotive and one hundred 190,000-lb hopper cars. If the locomotive exerts a friction force of 41,000 Ib on the rails in starting the train from rest, compute the forces in couplers 5 and 97. Assume no slack in the couplers and neglect friction. 3 2 1 100 99 98 Answers: Fs = Ib F97 = i Ib
The figure shows the cross section of a uniform 239-lb ventilator door hinged about its upper horizontal edge at O. The door is controlled by the spring-loaded cable which passes over the small pulley at A. The spring has a stiffness of 16.6 lb per foot of stretch and is undeformed when 8-0. If the door is released from rest in the horizontal position, determine the maximum angular velocity reached by the door and the corresponding angle 0. Answer: @max 4.2¹ rad/sec at 8-i
i need the answer quickly
A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 640 kg and an average gear-tooth force of 2.55 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assume r = 150 mm, R= 630 mm, 0 = 15% Detail of contact at B Answer: x= i B 14 ! mm
Dynamics
A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 740 kg and an average gear-tooth force of 2.60 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset X of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assumer = 110 mm, R= 695 mm, 0 = 24° Detail of contact at B Answer: X mm
Figure 2.2 shows a flower vase and trolley having a mass of 4 kg is pulled by a towing force T= 25 N at A. By using force and acceleration for rigid body method, determine: i. The acceleration of the trolley at this instant. ii. The normal reaction at wheel A and B. Note: Assume all the wheels are free to roll without slipping , the mass of wheels are neglected and the coefficient of friction between surface and wheel is µk = 0.35. G 10 cm JA 30° 25 cm T = 25 N В 50 cm 60 сm Figure 2.2 A flower on the trolley
The collar is released from rest in the position shown and slides down the fixed rod. Calculate (a) the stiffness k of the spring (which has been initially pre- compressed 50 mm by the light strap and wires) so that its maximum additional deflection equal 190 mm. (b) The nonnal 1.3 m smooth 10 kg 30 190 mm force N between the rod and the collar at the end position. Ui3= AT 1.0 m P = 250 N Position of B is fixed
A cylinder is rolling down a plane which has the angle theta with the horisontal. The cylinder starts from rest at height H. You can assume that the plane has the same static and kinetic coefficient of friction. 1. Draw the free body diagram of the forces acting on the cylinder while rolling, be sure you indicate the direction of the centre of mass 2. Write down an expression for the minimum coefficient of friction which ensures that the cylinder rolls and does not slip 3. The cylinder now rolls onto a flat surface. What is the speed of the centre of mass?
3. A 5-kg crate is released from rest at Point A of a 20-kg ramp which is inclined at 40 degrees as shown in the figure below. The lengths of the ramp is 2 m. The interface between the ramp and the ground can be assumed to be frictionless. Use Newton's 2nd Law and the definition of the center of mass to determine the horizontal distance that the ramp has moved when the crate reaches Point B. Neglect the size of the crate. Does your answer depend on the frictional force between the crate and the ramp? e S