The 14.6-lb lever OA with 9.6-in. radius of gyration about O is initially at rest in the vertical position (8= 90°) where the attached spring of stiffness k = 4.3 lb/in. is unstretched. Calculate the constant moment M applied to the lever through its shaft at O which will give the lever an angular velocity w = 5.9 rad/sec as the lever reaches the horizontal position 0 = 0. k= 4.3 lb/in, 13.6". 7.6" 13.6"

The 14.6-lb lever OA with 9.6-in. radius of gyration about O is initially at rest in the vertical position (8= 90°) where the attached spring of stiffness k = 4.3 lb/in. is unstretched. Calculate the constant moment M applied to the lever through its shaft at O which will give the lever an angular velocity w = 5.9 rad/sec as the lever reaches the horizontal position 0 = 0. k= 4.3 lb/in, 13.6". 7.6" 13.6"

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The system is at rest with the spring unstretched when theta = 0. the 5.3 kg uniform slender bar is then given a slight clockwise nudge. The value of b is 0.45 m. (a) if the bar comes to momentary rest when theta = 58, determine the spring constant k. (b) for the value k = 65 N/m, find the magnitude of the angular velocity of th ebar when theta = 38 degrees.
The 24-kg roll of paper has a radius of gyration KA = 90 mm about an axis passing through point A. It is pin supported at both ends by two brackets AB. The roll rests against a wall for which the coefficient of kinetic friction is = 0.2 and a vertical force F = 27 Nis applied to the end of the paper. (Figure 1) Figure 300 mm 125 mm 1 of 1 ▼ Part A Determine the angular acceleration of the roll as the paper unrolls. Express your answer using three significant figures. Enter positive value if the angular acceleration is clockwise and negative value if the angular acceleration is counterclockwise. IVE ΑΣΦΑ ↓↑ vec α = Submit Provide Feedback Request Answer ? rad/s² Next >
The slotted circular disk whose mass is 4.9 kg has a radius of gyration about O of 230 mm. The disk carries the four steel balls, each of mass 0.17 kg and located as shown, and rotates freely about a vertical axis through O with an angular speed of 164 rev/min. Each of the small balls is held in place by a latching device not shown. If the balls are released while the disk is rotating and come to rest relative to the disk at the outer ends of the slots, compute the new angular speed N of the disk. Also find the magnitude |ΔE| of the energy loss due to the impact of the balls with the ends of the slots. Neglect the diameter of the balls and discuss this approximation.
The strings AB and AC connect 500-g mass A to the vertical shaft BC. When the shaft rotates with a constant angular velocity of 15 rad/s, the ball has circular motion in the horizontal plane with the strings having angles of ? = 55° shown in the figure. Find the tension forces at the strings AB and AC.
The rod AB is non-uniform with a radius of gyration of 4.00 ft with respect to a horizontal axis through the center of mass G. It weighs 161 lb. At the moment shown the rod has a counterclockwise angular velocity of 3.00 rad/sec, and the spring is compressed by 2.00 ft. Calculate the force constant of the spring that will reduce the angular velocity of the rod to 1.50 rad/sec when it reaches the horizontal position. Assume the blocks A and B are weightless.
A momentum wheel for dynamics class demonstration is show. It is basically a bicycle wheel modified with rim band-weighting, handles, and a pulley for cord startup. The heavy rim band causes the radius of gyration of the 3.1 kg wheel tobe 275 mm. If a steady 32 N pull F is applied to the cord, determien the angular acceleration of the wheel. Neglect bearing friciton.
The slotted circular disk whose mass is 4.9 kg has a radius of gyration about O of 230 mm. The disk carries the four steel balls, each of mass 0.17 kg and located as shown, and rotates freely about a vertical axis through O with an angular speed of 164 rev/min. Each of the small balls is held in place by a latching device not shown. If the balls are released while the disk is rotating and come to rest relative to the disk at the outer ends of the slots, compute the new angular speed N of the disk. Also find the magnitude |AE| of the energy loss due to the impact of the balls with the ends of the slots. Neglect the diameter of the balls and discuss this approximation. 164 rev/min 145 mm 305 mm
Consider the wheel shown below with radius R, mass m, and radius of gyration ko¹ The wheel rolls without slipping under the action of a clockwise torque M. At the instant shown the spring with spring constant ks is unstretched. Derive an expression for the velocity of the wheel center of mass G after the center of mass has moved a distance d. (Hint: Use rigid body work-energy principles. The work done to the system by the applied moment is McA0 and A0 can be related to the distace d by the no-slip condition.) Us G R M м, ко ////
The 15 kg pendulum shown has its mass center at G and a radius of gyration about its mass center of kG = 200 mm and was released from rest when 0 = 0°. Spring AB has a stiffness of k = 200 N/m and is un-stretched when 0 = 90°. The angular velocity of the pendulum in rad/s at the instant 0 = 90° is: -0.6 m- а, 3.2 · b. 4.3 m . с. 3.6 0.1 m · d. 4.4 О е. 3.4 O f. 3.8 O g. 4.6
if mass (m)=345kg radius of gyration kG = 0.54 m θ= 200 degree 1) assuming no slipping and when starting from horizontal cable (θ = 0o) the spool moves to the left- determine the minimum tension in the cable (Tmin) that causes the spool to slip. Assumeμk = 0.4 and μs = 0.5.
The circular concrete culvert rolls with an angular velocity of w=0.58 rad/s when the man is at the position shown. At this instant the center of gravity of the culvert and the man is located at point G, and the radius of gyration about G is kg = 3.2 ft. (Figure 1) Figure @ 4 ft 0.5 ft 1 of 1 Part A Determine the angular acceleration of the culvert. The combined weight of the culvert and the man is 500 lb. Assume that the culvert rolls without slipping, and the man does not move within the culvert. Express your answer to three significant figures and include the appropriate units. α= Submit μA Value Provide Feedback Request Answer Units ***** ? Next >
The strings AB and AC connect 500-g mass A to the vertical shaft BC. When the shaft rotates with a constant angular velocity of 15 rad/s, the ball has circular motion in the horizontal plane with the strings having angles of a = 55° shown in the figure. Find the tension forces at the strings AB and AC. B 500g 400 mm 400 mm