The 120-N force is applied as shown to one end of the curved wrench. (a) If the value of alpha is 30 degrees calculate the moment of F about the center O of the bolt. (b) Determine the value of  angle alpha which would maximize the moment about O (c) state the value of this maximum moment.

Q: Problem 1 Determine the reaction at A and C. Support at A is fixed, C is roller support, and B is…

A:

Q: Only situation 4 solve it. All parts please i dont have questions post more can post again and again…

A: Reaction at A,E, C,D   As per guidelines we need to answer 3 subparts.

Q: draw the FBD.prove if statically determinate and solve all their support reaction.indicate the…

A:

Q: 5m 1.5 m 2m FB-60 N Fe=55 N 3m

A: Determine them which OA axes of flagpole and the angles θ and φ made between cables AB and AC.

Q: Determine the Maximum Normal ste developed stress in the bar buth at the cim section Containing the…

A: Stress concentration for the fillet -  wh = 5224 = 2.167andrh = 1424 = .5833Hence,K = 1.5   Maximum…

Q: #4 The beam is used to support a dead load of W k/ft, a live load of 2 k/ft and a concentrated live…

A:

Q: Solve for the EI A using conjugate, beam method 400 N/m 400 N/m To 2.3m EIA @ pt. B CV 2.2m

A: Given:Required:deflection at point B using conjugate beam method

Q: II A. USE THE PORTAL METHOD AND DETERMINE (APPROXI MAITE:) THE REACTIONS @SUPPORTS A, B, C ANDO. B.…

A: Note : Since you have asked multiple methods, we will solve the first method (Portal method) for…

Q: PROBLEM 03 A W, = 'ac' lb pipe is held in place by the vise. FA 30° FB B 50 lb

A:

Q: Determine the moment about O Given T= 670 r= 20 cm B AngleTheta = 40 degrees The pulley at B is…

A:

Q: F3-1. Determine the moment of the force about point O. 100 N 2 m 5m

A: Given,

Q: The rigid metal strip of negligible weight is used as part of an electromagnetic switch. Determine…

A: First, we draw the free body diagram for the above problem:-…

Q: Replace the two wrenches and the force, acting on the pipe assembly, by an equivalent resultant…

A: Consider the figure,

Q: The A-frame shown supports the 250-N load and 85-N load acting on horizontal member. It is hinged at…

A: To find pin reaction at B, C,D

Q: Determine (approximately) the reactions at the base of the columns of the frame shown in Figure. Use…

A: To Determine: The reactions at the base of the columns of the frame by using a portal method of…

Q: The frame shown in figure below is hinged to rigid supports at A and E. Find the components of the…

A: Note : BC and BD are 2 force members so they are subjected to axial forces only

Q: HW (4-1): If the area of each bar of the truss shown in 2w figure is (2700 mm') and the movement of…

A: Calculate the moment about A as; ∑MA=01×10-RD×cos4.5°×10+RD×sin45°×30=0RD=-0.707 kN Calculate the…

Q: T P Weld- -22.5° in. PROBLEM 7.41 Solve Prob. 7.19, using Mohr's PROBLEM 7.19 A steel pipe…

A:

Q: Determine the reaction moment at the fixed support A in N.m. Given that F= 5 N and L=3 m. Neglect…

A: To determine the moment along we have to determine the component of inclined forces and lengths.…

Q: H-3A tie rod 56x 125

A: Given Data:E=30×10 psiLoad = 200lb/ftH=3ftL1=6ftL2=2ft

Q: F = 25kN 1) The socket wrench AB lies in the plane parallel to xy plane. 10kNm The assembly OAB is…

A:

Q: Q. 5le 3 30 KN 120

A: Solution to question (1) (For Q2,Q3 please post separate question)

Q: b.) Using the value for F1,min that you calculated in (a), replace the two forces F₁ and F2 with a…

A:

Q: A. Reactions A and B B. Force in members GH,FH,GF, and FE. Identify if T or C

A:

Q: F4-1. Determine the moment of the force about point O. 600 lb 20 0.5 ft 5 t 30

A: Given that:

Q: If the load has a weight of 200 lb, determine the x, y, components of reaction at the…

A: Given : Weight = 200 lb Determine x, y and z component of reaction at the ball and socket joint A…

Q: 30kW intermal * hinge 40kW 20k N nteraat hinge マ 3m ' im' im 2m Im 3m

A: Hello dear this is the solution of your problem Please find the attached solution below, thanks

Q: 4 Two plates (14 in x 2 in) are welded to an I-beam (W12 x 16). Find the moment of inertia with…

A: Width of plate (b) = 14 in  Depth of plate (d) = 2in W12 x 16 beam section    To find : Moment of…

Q: 3/99 SS The uniform 15-kg plate is welded to the ver- ical shaft, which is supported by bearings A…

A:

Q: 3m 3m S

A:

Q: The beam is loaded as shown.What is the reaction at the roller?

A: Free body diagram -  Taking the span AB as horizontal axis, as it is asked to find only the…

Q: 1. Hibbeler 9-2 For the beam shown El is constant a) Use flexibility (method of consistent…

A: Objective: solve the beam using flexibility method. Solution: In this case we need to find the basic…

Q: A 3m 10N FV 1m 15N G 2m C 2m D 2m 10N H 1m E 3m B

A:

Q: A 3'-0" 400 lb 3'-0" B D с 600 lb 2'-0" 6'-0"

A:

Q: EQUILIBRIUM Smooth- bearing 1000+ 12* P4-121 Boll and socket! CHAP. 4 4-121. The homogeneous block…

A: given- force F=2000 lbangle at F=tan-1(56)=39.80o

Q: 450 N 30 0.2 m 200 N m 15 m- 2m 1.5 m 200 N

A: Solution Draw the diagram

Moments

There are various practical applications of the concept of moments, like a rotation of the crank due to linear motion of the piston, the moment of inertia and its use in designing beams and columns, bending moment concept, torque, twisting moment, etc.