9. The.... mode is used in cases where there is a need for communication inboth directions at the same time.a. Simplexb. Half-duplex e. Full-duplexd. Point to point10. In . . fiber optic, the density of the core decreases gradually from thecenter to the edges.a. Multimode step-indexc. Multimode graded-indexb. Single moded. None of them

As per bartleby policy, I am allowed to solve only one question Answer for 9 is Full duplex.

Answered: The . ..... mode is used in cases where…

The . ..... mode is used in cases where there is a need for communication in both directions at the same time. a. Simplex b. Half-duplex e. Full-duplex d. Point to point

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

The basic IC of the ALU unit in a computer system is Select one: O a. Decoder O b. Subtractor O . Comparator d. Adder
It is important to be aware of the distinction between programming in parallel and programming in serial.
2. Program counter 0 as with CLKo=1MHZ, to generate an square wave at OUT with period of 1s, where the 8253 is addressed by 80H-86H. (15 points) D7 SC1 D4 D3 D2 D1 Do RL1 RLO M2 M1 MO BCD D6 D5 SCO
Operation performed Result = Control сodes 1 00 0 01 1 01 1 10 A or B А - В A + B Α xor B A and B 111 9. Draw on the right the internal architecture of a one-bit ALU with the following function table:
If the four input lines of a multiplexer are D0, D1, D2 and D3, and the two select lines are given inputs as 1 1, then the output of the multiplexer is O a. D2 O b. DO O c. D1 O d. D3
Develop a simple automated industrial temperature regulator system for operating the coolant relief valve in a high-temperature furnace. When the temperature exceeds the safety threshold value, this will set the sensor ON which is connected to the input port of a microcontroller. The relief valve itself is connected to the output of the microcontroller. The safety system should work as described below: 1. The temperature sensor is connected to Port B, bit 3 of the microcontroller 2. The relief valve is connected to Port A, bits 1 and 2 of the microcontroller 3. When the temperature in the furnace exceeds the threshold value, the sensor sets the input port B, bit 3 to ON. 4. When the sensor is ON, the microcontroller sends an appropriate output to Port A inorder to open the coolant relief valve. 5. As soon as the sensor goes to the OFF state, the microcontroller clears all the output port bits thus closing the relief valve. Q1. A flowchart can be used to describe the step-by-step plan…
1.a. In your own words, describe the function of the "PCSrc" control signal and give an example of when the signal would be asserted and unasserted. b. In your own words, describe the function of the "MemtoReg" control signal and give an example of when the signal would be asserted and unasserted. c. In your own words, describe the function of the "ALUSrc" control signal and give an example of when the signal would be asserted and unasserted. d. In your own words, describe the function of the "RegDst" control signal and give an example of when the signal would be asserted and unasserted.
3- Perform the deconvolution operation between the following two signals: 2.5 2 1.5 4. 1 0.5 -0.5 -1 -0.5 0.5 1. 1.5 2 1.5 2.5 3.5 4 4.5 5 5.5 6 use matlab program
Here MATLAB code for the following. Write a program to calculate convolution of 2 signals in the time-domain.（Note: using own code, not internal function, is required）.
i) Build a 2-to-4 decoder with Enable and provide a picture or snapshot of the circuit here. ii) Build another 2-to-4 decoder Enable in the same workspace and join this decoder with the one in Part i) together to form a 3-to-8 decoder. Provide a picture or snapshot of the circuit here. iii)Use the 3-to-8 decoder you have constructed in part ii) to implement a full adder. Provide a picture or snapshot of the circuit here.
A 4-bits multiplier is to be implemented using Raspberry Pi. Your system should multiply two four-bits numbers A and B, and light up a LED if the result is greater than 128.a. Sketch the circuit schematic of your system.b. Sketch the flowchart of your design.c. Write the Python code needed using gpiozero library to satisfy the requirements of the system.
Connect the AVR ATMEGA 32 from Proteus to the Serial Port of the PC and a Switch to a pin on one of the PORTs. Write IN C the following program: If SW is pressed, released then pressed again (0, 1, 0 or 1, 0, 1 depending on your circuit), send "Hello" to the PC. If SW is pressed then released (0, 1 or 1, 0 depending on your circuit), send "Bye" to the PC. Modify and run the program in Activity 3 to transfer the data at the rate of 115200 bps (or the closest available to this value) Please be fast!