Terminal Velocity 3. Given: Atmospheric pressure = 101.3 kPA Air density = 1.20 kg/cubic meter Size of rain droplet; 0.6mm Temperature = 20 deg. C a. b. Determine; c. The force due to gravity and buoyant force in N. What is the drag force in N if the rain drop is in state of equilibrium? Consider vertical forces only If the temperature becomes 30 deg C (density varies), compare the terminal velocity, make a conclusion. Use drag coefficient same with 30 deg C.

Terminal Velocity 3. Given: Atmospheric pressure = 101.3 kPA Air density = 1.20 kg/cubic meter Size of rain droplet; 0.6mm Temperature = 20 deg. C a. b. Determine; c. The force due to gravity and buoyant force in N. What is the drag force in N if the rain drop is in state of equilibrium? Consider vertical forces only If the temperature becomes 30 deg C (density varies), compare the terminal velocity, make a conclusion. Use drag coefficient same with 30 deg C.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. Taking the coefficient of compressibility of water to be 2200 MPa, determine the pressure increase required to reduce the volume of water by (a) 1 percent and (b) 2 percent.
Consider a classically configured airplane with the following parameters: weight W = 120 kN !! wing area S = 50 m2 area of horizontal tail S = 12 m2 airplane lift curve slope C1a = 0.08 / degree tail lift curve slope CLa = 0.06 / degree horizontal tail volume V = 0.9 In two subsequent flight tests in air of density p = 0.55 kg/m³, the airplane is trimmed for straight, level and unaccelerated flight at different velocities. The following velocites v and associated tail incidences i, are recorded: Test 1 Test 2 Vx (m/s) 120 220 ų (degrees) 2.5 2.0 Use this data to calculate the static margin SM. Enter your answer as a decimal number (NOT in %) in the text box and upload your workings together with those of Question 1 as described in the instructions above.
Help
Choose the best answer among the following choices stated in each problem. Your choice must be supported with complete solution
'
Which is not true about laminar mixing?A. There is a deformation of fluid elements near the rotating part of the equipment.B. As the volume is held constant, the fluid elements must steepen.C. The reduction in size of droplets is an effect of shear and elongation.D. All statements above are true.
Water flows in a vertical channel. Use the given data to find the frictional pressure drop from the inlet to the exit of the channel. Compare the calculated values for ∆Pfriction by using the homogenous, the Reddy, the Friedel, and the Thom model. Data: H = 6 ft Dh = 0.145 ft P = 1000 psia Xe = 8% Vi = 3 ft/s Ti = 522 F.
There are two mercury barometers at the mountain. At the top reads 500 mm and at the base reads 650 mm. Determine the height of the mountain in meter. Note: the specific weight of air is in 12 N/m^3 and the specific gravity of mercury is 13.6
Q.1.A.A fluid has absolute viscosity of (0.001 Pa.sec). Calculate the velocity gradient and the intensity of shear stress at the boundary and at points (1, 2, 3 cm) from the boundary, assuming (a)- a straight velocity distribution (u=15y) and (b)- a parabolic velocity distribution (u-45-5(3-y)2), where (u in cm/sec) and (y in cm). Z حقاف
3-102 Consider a large cubic ice block floating in seawater. The specific gravities of ice and seawater are 0.92 and 1.025, respectively. If a 25-cm-high portion of the ice block extends above the surface of the water, determine the height of the ice block below the surface. Answer: 2.19 m Sea Cubic ice block 25 cm h
Determine the smallest acceleration that will cause the crate either to tip or slip relative to the cart. What is the magnitude of this acceleration? The coefficient of static friction between the crate and the cart is μs=0.5
2. A 15 mm diameter jet of water impinges normally at the centre of rectangular plate of size 100 mm x 100 mm x 4 mm with a velocity of 5 m/s. The top edge of the plate is hinged. Determine the force required to apply at the bottom edge to keep the plate vertical. What would be the angle by which the plate is deflected in the absence of resisting force? The density of plate material is 7850 kg/m.