Temperature (°C) 700 600 500 400 300 0 (AI) a 5 a+L 10 10 a +0 20 L 30 Composition (wt% Cu) 20 0+ L 0 (CuAl₂) 40 30 50 1200 1000 800 600 Temperature (°F) ) For the alloy represented by the phase diagram above, what is the wt% content of eutectic if an alloy of 2.5 wt% Cu s cooled very slowly from the molten state to 300°C?

Temperature (°C) 700 600 500 400 300 0 (AI) a 5 a+L 10 10 a +0 20 L 30 Composition (wt% Cu) 20 0+ L 0 (CuAl₂) 40 30 50 1200 1000 800 600 Temperature (°F) ) For the alloy represented by the phase diagram above, what is the wt% content of eutectic if an alloy of 2.5 wt% Cu s cooled very slowly from the molten state to 300°C?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. For the A-B alloy the phase diagram below, use the lever rule to find the amount of liquid and solid states and their compositions at Temperature T. Let Cx = 25%B, C =40%B, Cy = 60 %B Complete solubility of two metals in liquid and solid states (Ni -Cu ,Sb - Bi) TA M EM T EMa T Cy A B Concentration of B in A www.substoch com Temperature
2. Determine the amount of liquid phase in the a Cu-50% Ni alloy at 1300°C, % L 1500 1400 L. C +L 58 1300 1200 1100 1000 Cu 20 40 60 80 Ni Weight percent nickel Temperature (°C)
Give me right solution with clear calculations
What is the composition, in wt% Cr2O3, of the liquid phase in an alloy containing 71 wt% Cr2O3 at 2200C?
Question One (Compulsory) Composition (atk Sn) 100 20 40 60 80 327C B00 300 Liquid 500 232C 400 200 183C 07.8 18.3 61.9 300 100- H200 100 BO 100 20 40 60 Pb) Compesition (wt% Sn) Figure 1: Lead -tin phase diagram Figure I above shows a lead-tin (alloy) phase diagram. Consider an alloy composition of 55 wt% Sn - 45 wt% Pb. Answer the following questions: (i) Name the phases present and their compositions in the alloy at 150°C. (ii) Describe the structural and composition changes in the alloy when it is cooled from 190°C to 20°C. (iii) What are the compositions of phases at the eutectic point and why is this point important for the alloy? (iv) Given that the average density of a phase is determined as Pa = 100 ,calculate the PA PB volume fractions of the phases at the given compositions and at 150°C. Take the densities of lead and tin as 11.34 g/cm' and 7.36 g/cm' while the mass fraction of a is 0.21. (v) Name and describe four industrial applications of lead-tin alloys. ta aroundu (3.)…
Q/ The phase present for a 30 wt% sn, 7O wt% pb of alloy at 200°c is (a+ L) Determine: Composition of (a) and (L) for both (sn) and (pb). * 327°C 300E Liquid 232°C a +L 200E B + L 183°C 18.3 61.9 97.8 100 a +B 20 40 60 80 100 (Pb) Composition (wt% Sn) (Sn) Ca =18 Wt% pb, CL=58 Wt% pb and Ca =82 Wt% Sn, CL=42 Wt% Sn. Ca =20 Wt% pb, CL=60 Wt% pb and Ca =80 Wt% Sn, CL=40 Wt% Sn. Ca =22 Wt% pb, CL=65 Wt% pb and Ca =78 Wt% Sn, CL=35 Wt% Sn. Ca =15 Wt% pb, CL=63 Wt% pb and Ca =85 Wt% Sn, CL=73 Wt% Sn. Temperature ("C)
The binary phase diagram of metals P and Q is shown in the figure. An alloy X containing 60% P and 40% Q (by weight) is cooled from liquid to solid state. The fractions of solid and liquid (in weight percent) at 1250°C, respectively, will be 500 Liqas Liquid X 1250 Tanpentute PO 1000 100% P Solidas Solid 2027 40 60 60 80 100% Q Concentrative of Q un weight e
Please help me urgent
Should correct
Please answer within 2hr. I will give good ratings.
A hypothetical eutectic phase diagram for metals A and B shows that cooling a liquid melt with a concentration of 50 wt% A-50 wt% B to just below 625 °C (eutectic isotherm temperature) results in simultaneous formation of alpha and beta phases. The phase diagram also shows that alpha (A rich) and beta (B rich) phases exist at left and right extremes of the phase diagram, respectively. At the eutectic isotherm temperature, the maximum solubility of B in A and A in B is 10 wt% and 5 wt%, respectively. The phase diagram does not have any intermetallic compounds. A new solid alloy is made by melting together 86 gr of a 40 wt% A-60 wt% B alloy with 136 gr of 65 wt% A-35 wt% B alloy followed by cooling the melt to 400 °C. If the new alloy is heated up from 400 °C to just below 625 °C, answer the following questions: a. Calculate the overall alloy composition. b. Determine phases present and calculate their respective masses. Calculate the masses of the primary phase, eutectic phase, and…
a) The figure below shows three equilibrium structures that occur in an iron-carbon alloy, rank these from hardest to softest. b) The microstructure of an iron-carbon alloy consists of proeutectoid ferrite and pearlite. Relative mass to proeutectoid ferrite is 0.2 and pearlite is 0.80. How much carbon does this alloy contain?