Temp °C Pressure Specific Quality x "SH Enthalpy Entropy kPa Volume k/kg k/K-kg 10 m²/kg 201 Satu Vape 200 7.2505

Q: Consider the following linear equations -7x + 8y + 4z - 7x + (25 – k)y + 3z = 11 - 7x + 8y + (7 –…

A: The given set of equations are:

Q: What is the magnitude of the moment done by the force about the "z-axis" in the following figure.

A:

Q: The given sketch is a view of modified “Plate" one view. Sketch the 2D sketch of the below figure…

A:

Q: Draw the orthographic views of the following isometric figure.

A:

Q: Above is a 5 speed manual transmission gearbox. The gear selector fork is an assembly which the user…

A: Gear ratio is defined as ratio of driven gear's teeth to driver gear teeth. G1/2 = T2/T1 G1/3 =…

Q: Draw, using 1 st angle projection Orthographic view of the following figure  with  suitable scale,…

A: (a) the given front elevation;

Q: Cable AB has 5.0kN of tension. The tower pivots on the midpoint between A and C, level with the…

A:

Q: Given the isometric drawing of the solid, draw the multiview projection. L HRP FRP L FRP PRP L

A: Given the isometric drawing of the solid, draw the multiview projection.

Q: SKETCH THE 2D FIGURE IN AUTOCAD DRAWING AND USE THE 2D SKETCHING TO FIGURE OUT THE BELOW SKETCH

A:

Q: What is the magnitude of the moment done by the force about the "2-axis" in the following figure. 4…

A:

Q: A car has a velocity 176 ft/s. What is the velocity in MKS and CGS.

A: Given velocity of car is

Q: A. Find the value of tapered angle (a): Answer:

A: Find    The value of Taper angle

Q: can you help me understand this better. I am going to reproduce this drawing by using Creo. And i…

A: Here's a breakdown of the GD&T symbols used in the image:Datum symbols: A datum is a…

Q: The part below has a variety of features that are labeled as datum features. Assume all are primary…

A: A moment of inertia is a mass of the body when a body is rotating on an axis. The moment of inertia…

Q: Q2 - The frame shown in the figure is loaded at point E with a force F = 600 N. Calculate the moment…

A: From the figure given in question, Coordinate of E,E=0,75,100Coordinate of H,H=300,0,200Position…

Q: Draw a Miller index direction of the following (below) on a 3D coordinate system. 1. [1 2 3] 2.…

A:

Q: Bearings are used in automobile, these parts are produced by casting process . Below figure shows a…

A: Open Creo application and click on "New"   Select "mmns_part_solid" from given list and uncheck…

Q: Given the vector in the figure above has a magnitude of 23.8 [N], what is the z-component of the…

A: Given data: F=23.8 N Need to determine the z-component of the vector.

Q: Draw the isometric figure given the views below. Will thumbs up if correct. Thank you.

A:

Q: AutoCAD Sketching The given sketch is a cross section view of housing. Sketch the 2D sketch of the…

A:

Q: Can you write me a program manuscript using geometric definition on FAPT language. The starting…

A: To create a part program for the given part drawing (Fig. 2) for a wire electric discharge machine…

Q: How many possibilities are there to represent the orientation of a frame (B) relative to a fixed…

A: Given:Fixed angle convention.To find:(a) Number of possibilities to represent the orientation of a…

Q: Given the following figure, what is the resultant force due to the distributed load? Units are taken…

A: In the given figure, force distribution diagram is shown. The force is a function of x. It is…

Q: A motorcyclist left from his work at 5:45 in the morning and arrived at the coffee shop 42 km away…

A:

Q: A cube has a volume s³. If the edge length is initially 4.20 inches, and the cube is heated such…

A:

Q: (xo, Yo) Ay = Number (x,y) m 00 Given the above graph plotting y position against a position, where…

A: xo = 0 myo = -4 mx = 5 my= 0 m

Q: A pyramid ABCD, the hend poiut A(2,5,4) and basepeints B(2, 0.5,0), C(O.5,2,0 and D(-,0,0). Reflect…

A: Given data The points are A (2,5,4)B (2,0.5,0)C(0.5,2,0)D(-1,0,0)

Q: Draw isometric view of casting, two views (FV and SV) of which are shown in figure in First angle…

A: Given question: Draw isometric view of casting, two views (FV and SV) of which are shown in figure…

Q: What's the median of the following points? x = Type your answer... [-3 3 4 2 -1 1 4 5]

A:

Q: sketch the 2d figure using autocad and colour the hatching and reference lines

A:

Q: Barry enjoys doing bicep curls at the gym. In a bicep curl, Barry's forearm is rotated around his…

A:

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: Simplify the following expressions (note that dij is the Kronecker delta, repeated index means…

A: a) The Kronecker delta is equal to 1 if the indices are equal and 0 otherwise. Therefore, δtt = 1.…

Q: Please give answer clearly with each steps.

A:

Q: using creo parametric software draw the following Sketch isometric views based on the given Cavalier…

A:

Q: Q7) If point A and B are center for fillet of R10 and R20 respectively. What is the length of…

A:

Q: and that 985 kilonewtons [kN] of dirt are removed from the ground for the pool. Determine the depth…

A: Given that ;   Area, A = 7 x 3 m2  Force, F = 985 kN Specific gravity =2.1

Q: Given the views below, sketch the isometric figure . You may use @ut0c@d to draw the figure

A: we need to draw the isometric view with the help of the given three orthographic projection views.

Q: FOR THE FOLLOWING FIGURES ISOMETRIC VIEW IS NEEDED  Sketch theisometric view using the below…

A:

Q: A all the В almost all of the very few of the about half of the

A: Answer :[A] All the

Q: Draw the three projections of the body in Figure 1- using AutoCAD 1-Do not write the dimensions on…

A: Find Draw the three projections of the body.

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.