Technician A says that load-carrying ball jointsshould always have some play in them. Technician Bsays that follower ball joints should never have someplay in them. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor B

Q: Technician A says that some small cracks in the accessory drive belt may be within tolerance.…

A: Technician A says that some small crack in the accessory drive belt may be within tolerance limits.…

Q: For the pulley system below, which equation is true about the length of the cord marked as green? If…

A: To find: The length of the green cable.

Q: Technician A says the size of the pads, shoes, drums, and rotors is based on the weight of the…

A: A drum brake is a brake that uses friction caused by a set of shoes or pads that press outward…

Q: A __________ hook has a narrow throat so that it will grab a link in the chain and not slip. Select…

A: Hooks is an instrument or component which is used to elevate the heavy loading.

Q: Technician A says the size of the pads, shoes, drums, and rotors is based on the weight of the…

A: 1.   A drum brake is a brake that uses friction caused by a set of shoes or pads that press outward…

Q: When discussing shift problems, Technician A says that worn or broken engine and transaxle mounts…

A: A chain of gears which is used to pass on the power to the wheel from the engine is called as…

Q: The CV joint boots on the left side of a vehicle appear to be squeezed together; the boots on the…

A: The function of engine mounts is to limit the movement of the engine, hold it in a position and…

Q: Technician A says that the piston seal retracts the caliper piston when hydraulic pressure is…

A: Technician A is correct.

Q: While discussing the different types of pressureplates: Technician A says that coil spring types…

A: Option D is the correct naswer

Q: True or False: Frictionless 2D Pins and 2D Hinges have reactions in both the x and y directions.…

A:

Q: A car jumps out of gear into neutral, particularlywhen decelerating or going down hills: Technician…

A: The gear system in the cars is used to transmit the power from the engine to the wheels as per the…

Q: The rotation angle of the joints is still needed.

A:

Q: Technician A says that broken or worn engine and transaxle mounts can cause a transaxie to have…

A: Given Transaxle problem To find Statement with is/are correct Shifting problem of transaxle can be…

Q: When reviewing the service procedures for CV joints and drive axles, Technician A says that the axle…

A: The axle can be used as a slide hammer to help remove a stubborn inboard joint from the transaxle as…

Q: Technician A says a metric bolt with the marking of 8.9 has more yield strength than a 10.9 bolt.…

A: Technician A is not correct as the 10.9 grade bolt has more strength than 8.9 grade. Grade 10.9 is…

Q: 1) The working face of ordinary flat key is 1 A. Side B. Upper top surface C. Bottom surface D. End…

A: (1)

Q: When reviewing the procedure for replacing an axle boot, Technician A says that the position of the…

A: Understand that when the old boot is removed the new boot is used to replace the old one at the same…

Q: Technician A uses a micrometer to measure the connectingrod journal for taper. Technician B uses…

A: In this problem, it is asking that which technician is correct.

Q: The shorter the __ is, the more force the lever will apply. A. Fulcrum  B. Acceleration  C. Load…

A: The heavy load can be handled with small effort through mechanical advantage of a mechanism. In…

Q: Technician A says a bolt may become fatigued if it is over tightened. Technician B says that a bolt…

A: The bolt will be fatigued in both the overtighten and under-tightening cases

Q: Technician A says a sticking inboard joint can cause the car to shimmy during acceleration.…

A: Solution:

Q: A vehicle makes a loud clicking sound during a left turn; during a right turn, the clicking noise is…

A: Solution:

Q: Large cars with long drive shafts often use a double-U-joint arrangement called a __ .a. Spicer…

A: A universal joint is a mechanical connecting device that is used between the rotating shafts and the…

Q: A ball and a socket joint forms a

A: A ball and a socket joint is a form of synovial joint in which socket swivel around the fixed ball.…

Q: Technician A says that the piston seal retracts the caliper piston when hydraulic pressure is…

A:

Q: When installing a new release bearing, Technician A says the outer surface of the transmission's…

A: The bearing is the rotating element that is used to transmit the rotary motion. Bearing are of…

Q: A link which transmits the motion with negligible deformation is called as   a. rigid link. b.…

A:

Q: hoose the correct device pair from the following which is a common example for lower pair and…

A: Option D is correct  Nut and bolt

Q: Technician A says that most transaxles have a countershaftbetween the main and output shafts.…

A: Main shaft is generally the crank shaft which is attached to the engine directly. And output shaft…

Q: Which of the following screwdrivers is like a Phillips but has a flatter and blunter tip? a.Standard…

A: Given Data : Screwdrivers Phillips

Q: va three DoF (Degree of freedom) eight link (n=8) mechanism with rev rify DoF mechanism using…

A:

Q: Differentiate between a fast and loose pulley.

A: Difference between fast pulley and loose pulley is given below.

Q: Draw FBD of Bicycle axle (Thru axle)

A: To find :- Fbd of axle

Safety guidelines for material handling

Material handling involves transportation and movement of materials (inventory) within the storehouse or warehouse. The process also involves efficient inventory management, which forms an essential part of any manufacturing or fabrication company.