Task IVYou are working as an Electrical Engineer in NEPCO company your manager asked you to helptechnicians to analyze the exponential signals in addition to the stored and transmitted signals in anewly developed transformer and find the results as a part of a project to test the quality of thetransformers to be reviewed by the quality assurance team (QA).Your manager asked you to evaluate the following using MATLAB:a. Plot the following exponential functions on the same figure, call it Figure (1):f₁(t) = 10 etf₂(t) = 10 e²t2tf3(t) = 10 e-t b. If the current flows in a charging inductor i(t) at time t seconds is given by:i.ii.iii.i(t) = 1; (1 − e 7)m²Where Is is the supply current, Is = 45 mA and t= 20.Plot the graph of i(t) on separate figure, figure (2)From the figure find the current flows in the inductor after 24 seconds.The time t taken for current flows in the inductor to reach 30mA if the supplycurrent Is remains at 45 mA.c. Compare the figures that are obtained in parts a and b and discuss your results.

a) Given:functions,To do:Plot all signal in one figure. b) Given:Charging inductor current,with, To…

Task IV You are working as an Electrical Engineer in NEPCO company your manager asked you to help technicians to analyze the exponential signals in addition to the stored and transmitted signals in a newly developed transformer and find the results as a part of a project to test the quality of the transformers to be reviewed by the quality assurance team (QA). Your manager asked you to evaluate the following using MATLAB: a. Plot the following exponential functions on the same figure, call it Figure (1): 2t fi(t) = 10 et f₂(t) = 10 e²t f3(t) = 10 e-t

Task IV You are working as an Electrical Engineer in NEPCO company your manager asked you to help technicians to analyze the exponential signals in addition to the stored and transmitted signals in a newly developed transformer and find the results as a part of a project to test the quality of the transformers to be reviewed by the quality assurance team (QA). Your manager asked you to evaluate the following using MATLAB: a. Plot the following exponential functions on the same figure, call it Figure (1): 2t fi(t) = 10 et f₂(t) = 10 e²t f3(t) = 10 e-t

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

by High Voltage
The EMF equation of transformer referring to primary turns is Select one: O a. 4.440N,B O b. 4.440 fN. mi OC. 4.440 N,A O d. 4.440 fN,
A voltage multiplier has 12 stages Capacitances, all equal to 0.08 μF. Thesupply transformer secondary voltage is 150 kV at a frequency of 100 Hz. Load current 0,006A.What is the percentage ripple, the regulation and the optimum number of stages for minimumregulation or voltage drop.
DC 200 V was applied to the primary of a transformer with a conversion ratio of 1/5. Obtained from seconderexplain the reason for this by typing the voltage value to be?
I need the answer as soon as possible
Q5. A 20 kVA, 2000/200-V, 50-Hz transformer has a high voltage winding resistance of 0.2 2 and a leakage reactance of 0.240. The low voltage winding resistance is 0.05 and the leakage reactance is 0.02 2. Find the equivalent winding resistance, reactance and impedance referred to the (i) high voltage side and (ii) the low-voltage side. (Draw the related equivalent circuits)
Given a 100-ohm resistor. What is the la place transform of its voltage?
Approximate solution time is 5 minutes. A transformer supplies power to a feeder that has five customers. Daily maximum demands for these customers are 120 kW, 40 kW, 90 kW, 110 kW, and 180kW. The maximum demand on the feeder is 243kW. The coincident factor of the feeder is
An AC source provides peak output Vi and peak current ii when connected to the coil primary of a transformer. The transformer has Np turns in the primary coil and Ns turns in the secondary coil. A resistance circuit R is connected to the transformer, see figure below. What is the equivalent resistance of the circuit?
solve using a transformators topic At a 115 kV input transformer with 300 turns, determine the output voltage if it has 200 turns.
I need the answer as soon as possible
don't copy