Task 7 (25 points) A solid concrete wall 4.0 m by 2.4 m and 30. cm thick, with a thermal conductivity of 1.3 W/(m-K), separates a basement at 18°C from the ground outside at 6.0 °C. a) Under steady state conditions, how much heat flows through the wall in one (precise) hour?

Task 7 (25 points) A solid concrete wall 4.0 m by 2.4 m and 30. cm thick, with a thermal conductivity of 1.3 W/(m-K), separates a basement at 18°C from the ground outside at 6.0 °C. a) Under steady state conditions, how much heat flows through the wall in one (precise) hour?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

The specific heat of liquid water is 4190 J/kg. K. ▼ Part A What is the molar specific heat of liquid water in J/mol. K? Give your answer as a multiple of R, rounded to the nearest half integer. Express your answer as a multiple of R to the nearest half integer. Cmol = 9 R Submit Correct Part B Previous Answers Equal moles of liquid water and helium gas are heated at constant pressure from the same initial temperature to the same final temperature. By what factor is the entropy increase of the water larger than the entropy increase of the helium? Express your answer to two significant figures. AS water ASHe Submit 17| ΑΣΦ Request Answer ?
3 of 4 A stainless-steel-bottomed kettle, its bottom 25 cm in diameter and 1.6 mm thick, sits on a burner. The kettle holds boiling water, and energy flows into the water from the kettle bottom at 800 W. Review I Constants I Periodic Tabl Part A What is the temperature of the bottom surface of the kettle? Thermal conductivity of stainless steel is 14 W/(m K). Express your answer using four significant figures. VO AEO ? T = 102.65 °C Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining Review your calculations and make sure you round to 4 significant figures in the last step. Ne Provide Feedback
1. R-134a at state 1 is contained in a piston-cylinder device at T₁ = -12°C and P₁ = 0.2MPa. = 25V₁. Heat is then added at 80°C. = The fluid is heated at constant pressure to state 2 such that V2 constant volume until it reaches state 3 the temperature T3 a. Show the process on a T-v diagram. b. Calculate h1, h2 and h3.
A 72° object is placed into a 3272º furnace and it takes 10 minutes for it to reach 1000 (Recall, T = TR + D, ekt) a. Find the equation that models the temperature at a given time. b. How long does it take for the object to reach 2552°?
How much thermal energy needs to be extracted for the temperature to drop to 3x10^2 K? USE IMAGE AS REFERNCE
Q1
Question 3 Hot gases at 280°C flow on one side of a metal plate of 10mm thickness and air at 35°C flow on the other side. The heat transfer coefficient of the gases is 31.5 W/m² K and air is 32 W/m²K. What is the overall heat transfer coefficient if the thermal conductivity is 50 W/m K? Next ▸
When a 270-g piece of iron at 160 °C is placed in a 95-g aluminum calorimeter cup containing 250 g of liquid at 10° C, the final temperature is observed to be 35 °C. The value of specific heat for iron is 450 J/kg·C°, and for aluminum is 900 J/kg · C°. Part A Determine the specific heat of the liquid. Express your answer using two significant figures. VO AE ? J C = kg-C° Submit Request Answer
SECTION B Answer ALL Questions An iron plate 2cm thick has a cross-sectional area of 4000cm2. One face is 160°C and the other at 130°C. If heat passes through the plate each second equals 40 kJ, calculate the thermal conductivity of iron. 2. (a) (b) An electric heater supplies 13500 J of heat energy to a metal block of mass 500g. The temperature of the block rises from 20°C to 80°C during the heating process. Assuming that very little heat is lost from the block during the heating process, what is the specific heat capacity of the metal?
Problem Set 11 (Calorimetry) In a calorimetry experiment, a 60 g metal sample was heated to 100°C, and then quickly transferred to a styrofoam cup with cover and containing 100 g of water at room temperature (23°C). After carefully swirling the calorimeter, the final temperature of the water was recorded at 27°C. Calculate for the specific heat capacity (Cm) of the metal sample. Assume that the specific heat capacity of water (Cw) is 1 cal/g.C°.
The cat is fat. The cat’s fur and the cat’s fat provide the same amount of insulation. How much kitty blubber is equivalent to 1.0 cm of fur with regards to heat transfer by conduction? Please put it in this formatting.
A person consumes about 2700 Cal a day. 1 Cal = 4186 J, and 1 kWh = 860 Cal. Part A What is this energy in joules? (2 sig figs) Part B What is this energy in kilowatt-hours? (2 sig figs) Part C If a power company charges about 10 ¢ per kilowatt-hour, how much would this energy cost per day if the person bought it from the power company? (2 sig figs)