Pls correctly thanks with explanation Bending stressIn this exercise, we consider the cantilever beam of length L = 12m, shown in the figure below, subject to end moment Mo = 10kN. m.МоTask 1. Calculate internal moment M (in kN·m) in the beam's cross-section located at oconvention shown below.=3.0m from the fixed end. Don't forget to take +/- sign into account, using signΧρMoM=-10Your last answer was interpreted as follows: -10Correct answer, well done.MMMMPositive bending momentNegative bending moment

Answered: Image /qna-images/answer/df802622-4270-4e4b-8be2-91c324c5282d.jpg

Task 1. Calculate internal moment M (in kN m) in the beam's cross-section located at x0 = 3.0m from the fixed end. Don't forget to take +/- sign into account, using sign convention shown below. Χρ Mo M M

Task 1. Calculate internal moment M (in kN m) in the beam's cross-section located at x0 = 3.0m from the fixed end. Don't forget to take +/- sign into account, using sign convention shown below. Χρ Mo M M

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 4) Select ALL choices which may be indirectly controlled by Surface Profile IF NO DATUMS ARE USED A…

A: Surface Flatness Perpendicularity

Q: If A = Gax + 3a, and B = 8'ax + 2ay-8 az, %3D (a) find the dot product (b) find OAR

A: GivenA→=6i^+0j^+3k^andB→=8i^+2j^-8k^

Q: A chain drive is required to transmit a design power of 4.13 kW from a motor to an output shaft. The…

Q: Can you help me with this problem?

A: The image shows a part drawing for a wire electric discharge machine (EDM). The objective is to…

Q: Ex. #1 central pitch. The dedendum equals 1/P, inch, the clearance is to be one-eight of the…

Q: Write a note on different types of gear along with application.

A: The gears are used for power or torque transmission. They are generally used whenever the positive…

Q: Draw digitally a unique, original design of a decorative block. Please refer to the sample picture…

A: A decorative block can be any type of block or object that is used for ornamental or aesthetic…

Q: In Figure below, the main issue is with the leader representing which item?

A: Given:- An engineering drawing To find: Which representation is wrong

Q: Please look at pic. Please help, I don't get part b. Thanks

Q: I need answers to this part, thank you.

A: The correct matches are:

Q: I have three parts that I need answered pertaining to the print provided below. Do the dimensions…

A: It is mentioned in the drawing specification that “dimensions and tolerances apply before the…

Q: 11) Define the cornering stiffness.

Q: What kind of font is typical for usage in engineering diagrams?

A: To find: The type of font used in engineering diagrams.

Q: In general, Fair Use allows small sections of a work to qualify for copying so long as the entire…

A: Given:

Q: Could ypu help me with this problem? It should start with something like this: P1=0,0 P2=10,0…

A: The part program for the given drawing uses the Fanuc Cut language. I'll start by identifying key…

Q: 360 degrees of crankshaft rotation. 1. A revolution is 720 2. The camshaft rotates degrees during…

A: To find :- Fill in the blanks

Q: What best describes this print? * A. Casting B. Forging C. Welding D. Machining 2. There are GD&T…

A: First of all, In the given Engineering drawing the Rotor assembly is given and its parts are drawn…

Q: A hammer weighing 60N hits the block that rests on the spring shown. The striking velocity of the…

Q: In the context of our teaching and learning, which one of the below statements is mostly correct…

A: The correct option is second.

Q: Drilling and Completion Engineering II An exploration well is to be drilled to a total depth of…

Q: Create a list of operations for the blueprint provided below. The list of operations must be in…

A: The chronological order of operation of the given part is mentioned below for this part the list of…

Q: Problem 7 Trekking handlebars or "butterfly bars" are popular with long-distance cyclists because…

Q: In a turning operation on carbon steel with hardness- 175 HB. the cutting speed - 225 m/min, feed-…

A: GivenV=225m/minf=0.25mm/revd=7.5mmη=90% Cutting energy for Brinell hardess 175Hb=1.6J/mm3U=1.6J/mm3

Q: G R.75 00.63 THRU E 01.123 F0.250 T 2.00 1.00 1.38 1.123 mm diameter hole with depth of 0.250 mm…

Q: Known values: L Rp Wdisk a disk 0.9 m 0.4 m 33° 30° 10 rad/s 10 rad/s? .2 Problem Statement: A disk…

A: Peg attachment mechanism:- In the case of spinal disc replacement options, we can conduct many…

Q: now the 12-tooth gear turn?

Q: Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with…

Q: In the context of our teaching, which one of the below statements is mostly correct about in…

A: Component design, sometimes known as atomic design (though we prefer "Component design" at…

Q: I need these two parts answered (Multiple Choice). If you can not answer all two parts please leave…

A: Problem 1To determine the tolerance specified for the depth of groove in the enlarged view, refer to…

Q: H.W praw load dingram alesfanding to the given-Shar dingram? 2nd (urve 10 2nd Garve sfin -10 Im Im

A: BMD(Bending moment diagram) is a diagram representing the variation of bending moment along the…

Q: I need answers to parts 7, 8, and 9, pertaining to the print provided.

A: What is the basic height of this assembly as shown in the section view?Refer the front section…

Q: 500 kN.m T KN. m/ m В C 2 m 3 m 5 m Q/Find the value of T (kN. m/m) So that the value of angle of…

A: Given Data Angle of twist at D is zero At A is fixed support so the angle of twist at A is zero…

Q: Hi, I am needing help with a formula to calculate fabric cost. Sample: 1. Fabric used per piece,…

Q: Which machine would you recommend given the following information and interest rate is 10%? New Used…

A: Given data as per the question Interest rate = 10% Calculations considering 1st machineInital cost…

Q: Select the correct statement below regarding the two solid model parts shown. (A) (B) It is easiest…

A: In the figure two solid model parts are given. The extrusion is in which the two dimensional shape…

Q: Match the following. Forging is an example of Choose. Choose. Drilling operation is an example of…

A: Forging is an example of Primary shaping process

Q: I don't understand due to the way its written, can it be written again but more clearly pls

A: From the question, the given data are: Volume of heater = Capacity of heater =V1 = 2 liters = 2 x…

Q: I need answers for problems 13, 14, and 15 pertaining to the print provided. NOTE: If you refuse…

A: 13.A characteristic of a system which may cause failure or defects if not in line with quality…

Q: You've been asked to design a stamping tool as shown. What are the internal forces at A and B? Ans:…

A: Draw FBD of the given system

Q: Can you help me with this please? For a given part drawing fig. prepares a Part program for a wire…

A: To write a part program for a Wire EDM machine using Fanuc - Cut, we need to consider the geometric…

Q: Explain the following with appropriate examples (at least 2 examples) 1. Grubler's criterion. 2.…

A: The Grubler's criterion gives the number of degrees of freedom of a mechanism involving links and…

Q: 7. Using the drawing below as a reference, Change "101" refers to which feature on the drawing? A.…

A: according to the drawing

Q: I need answers to questions 1, 2, and 3 pertaining to the print provided. Note: A tutor keeps…

A: Answer to question no. 1Yes, the print shows the detail drawing of a single part here. The drawing…

Concept explainers

Bending Moment

In general, we can define the bending moment as the reaction induced when a certain amount of load or force is applied to an element which makes it bend.

Question

Pls correctly thanks with explanation

Bending stress
In this exercise, we consider the cantilever beam of length L = 12m, shown in the figure below, subject to end moment Mo = 10kN. m.
Мо
Task 1. Calculate internal moment M (in kN·m) in the beam's cross-section located at o
convention shown below.
=
3.0m from the fixed end. Don't forget to take +/- sign into account, using sign
Χρ
Mo
M=-10
Your last answer was interpreted as follows: -10
Correct answer, well done.
M
M
M
M
Positive bending moment
Negative bending moment

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Moment calculation in beam at x=3m

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

20)
Required information Jobe Concrete Products placed a new sand sifter into production 3 years ago. It had an installed cost of $100,000, a life of 5 years, and an anticipated salvage of $20,000. Book depreciation charges for the 3 years are $42,000, $18,000, and $22,000, respectively. If the sifter's market value today is $20,000, determine the difference between its current book value and its market value. The difference between its current book value and its market value is determined to be $
F, = 50 N F2 = = 40 N -5 45° F1 = 20 N
I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
What’s the correct answer for this please?
1A
Number 4
I need parts 4, 5, and 6 answered pertaining to the print provided.
If the answer is no can anything be done to save the part?
ll a O ... 73 Your email address will be recorded when you submit this form. Not ahmed.yahya.engmsy@student.uobabylon.edu .iq? Switch account Required Q2:- To avoid interference, the value of the addendum must be:- * None of these On the gear is less than that of the pinion. All of these. On the pinion is equal to that of the gear. On the pinion is more than that of the gear. Q5:- The minimum number of pinion teeth in the rack and pinion arrangement of standard gear and pressure angle 20
Don't need to show work, just need to know which ones correct to compare my answers. 9.10.
Summary/Conclusion Discuss the strengths of your design and how it met the specifications. Discuss your assumptions and why they are valid. Discuss what you might change about your design in a redesign effort. Format: The project should be presented as a design report using a word processor. Include any hand calculations in an appendix. More details will be provided. Choose to design either a slip-jaw or channel-lock pliers to last for 25 years of use by a professional. Use an appropriate tool steel for the pliers. Design for 95% male grip force. Use a minimum factory of safety of 2.50. Determine dimensions not given. Slip Jaw Pliers A= 9.00 inches B=1.00 inches C= ? D=1.25 inches H= 1.875 Inches D B A