Targer than in steel shaft. Q1) For the section shown aside, if the bending stress at point B is 225 MPa, what is the maximum bending stress on the cross-section? 20 mm A) 225 MPa B) 170 MB.

Q: Calculate to the correct number of significant figures. (3.14x2.4367) - 2.34

A: The problem is given as, In this, it can be seen that the minimum significant figure of the number…

Q: what is 6 to 10 po?

A:

Q: 5. Work-energy principle to be useful in determining the change in the speed of a particle during a…

A: Work energy principle to be useful in determining the change in the speed of a particle during  a…

Q: i cant read this.. can you write it out??

A:

Q: Q1: Find the resultant force and the component force F for the system shown below (fig 1) using…

A: Calculated the resultant force and the component of force F for the system using parallelogram law.

Q: What about the 100N weight?

A: There is a thin triangular plate in x-y plane.And location for the center of gravity is to be find…

Q: Forces and moments are scalar Forces are moments are vector quantities.

A: Forces and moments are both physical quantities that can be used to describe the behavior of objects…

Q: 3

A:

Q: 7 Doorbe Daanbe the proccdoe lor cvalvahon crnd Cncl improement f laaul. ?

A: Systematic Layout Planning Procedure:- It is a procedure layout design approach developed by Muther…

Q: Create a free hand isometric drawing of the three objects

A: Free hand isometric drawing of all three components are drawn below...

Q: What does shear strains cause?

A: Answer Shear Strain : it is the angular displacement from the original position

Q: Given the points A( – 5, 6, – 4), B( – 2, — 10, 6), and C(4, 0, 5), find (a) the angle between AB →…

A:

Q: 1. What is the type of robot?

A: ***As per our company policy we are supposed to do only 1 question if you need the rest please…

Q: What are the different types of force? Applied Tension Gravitational Spring Air Resistance Normal…

A: (I) Force has been classified on the basis of contact which is as follow 1. Contact force:- These…

Q: Name the following figures.

A: Pneumatic Cylinder Pivot Bracket with rigid bearing AB7

Q: A plastic rod AB of length L = 520 mm has a diameter d, = 30 mm as shown in Figure Q2(b). A plastic…

A: For the given composite bar it is required to determine: (1) Total elongation of the bar when P = 15…

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: what is 1.54 from?

A: Given:The length of CD is .The length of BC is .The length of AG is The length of AD is .Consider…

Q: solve frist one please

A: The diametral pitch of each gear:center distance of the gears:Velocity ratio:

Q: Solve for the mobility. Show your logical and accurate solutions after every fig

A:

Q: A plane's propeller can be modeled as a thin, uniform rod that rotates about its frictionless center…

A: Given data  F = 591 N  L = 6.51  m  mass of propeller (m) = 10.1 kg    To determine  (a) direction…

Q: b) Determine the March number of the bullet for both medium.

A: (b) Consider the helium gas and calculate the speed of sound in helium. cHe=γRTMFor γ,…

Q: □ 18 F.V.

A: According to the details provided in the question, we need to draw three projection views.

Q: (4) 8.8.8.8 16 8 8 16 21

A: the question is not fully asked   bricks and blocks are given

Q: what is part number 4

A: Solution:

Q: Is this definitely correct? A few calculators online such as BMEP calculators give me a different…

A: Given data:Torque = T = 100 NmEngine is four stroke,so there is one power stroke after two…

Q: From the projected views obtain the isometric drawing.

A: According to the details provided in the question, there are three views of the first angle of…

Q: D raio s.f.D and B.M.

A:

Q: how can I get the 85 α

A:

Q: Please give the details explanation of the answer

A:

Q: R D.

A:

Q: So what is the answer? What is y (1)? What is the answer up to two decimal places.

A: y(1) for equation of motion

Q: 583 mK/s = ________ μK/ms 2. 583 mK/s = _______ K/s

A: Given data 1. 583 mK/s = ________ μK/ms 2. 583 mK/s = _______ K/s

Q: A Tyrannosaurus named Rex was having a birthday. He was standing on one end of a cart that rolled…

A:

Q: What is the Falling Block?

A: Falling block: The falling block is an action in which a solid metal slides vertically in a grove…

Q: Q3/ For the plate shown in figure below find * (a) ΣΑ YA 7 9. X 8 5

A:

Q: The water is siphoned out of the tank shown in Figure 4 (b). Determine the flow rate from the tank…

A: According to the problem, the water is siphoned out of the tank so the pressure at the end where the…

Q: ) Newton's Law of Universal Gravitation states that the force exerted between 2 objects, called a…

A: Data given-  F = G m1m2 / r2

Q: How do you know that it is -1.2? What determines the sign?

A: Given: How do you know that it is -1.2? What determines the sign?

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.