Table no. 1 Find the colour of resistance No. Value of Theoretical resistance 1 1100 2 2 10000 Q 3 2200 +10% Q 4 3700 2 4000 2 Table no. 2 Find the value of resistance No. colour of resistance Theoretical 1 Brown Violet Brown 2 Red Yellow - Red 3 Violet - Green - Red 4 Brown Black - Orange 5 Red - Green - Orange

Table no. 1 Find the colour of resistance No. Value of Theoretical resistance 1 1100 2 2 10000 Q 3 2200 +10% Q 4 3700 2 4000 2 Table no. 2 Find the value of resistance No. colour of resistance Theoretical 1 Brown Violet Brown 2 Red Yellow - Red 3 Violet - Green - Red 4 Brown Black - Orange 5 Red - Green - Orange

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Calculate the voltage across R1 , R2 and R 4....also the current across R3. R1(color coded) = blue,yellow, red, gold R 3 (color coded) = Orange, green, brown, silver Note: use maximum value on the resistance tolerance..ex. 200 ohms +/- 5% = 210 ohms
Answer the following questions by referring to any reliable sources
Please help. Show clear and concise explantion. (Detailed Solution) with illustration/graph. Thank you!
A copper cable with a length of 1.00 m starts to conduct a current of 5.00 A when it is connected to a 4.50 V de source. Given that resistivity of the copper, Pcopper = 1.68 x 10-8 2 m. (a) Calculate the resistance of the copper wire. (b) Find the diameter of the copper wire. (c) It is found that the current in the copper wire drops to 4.40 A when its temperature rises by 35.0 °C. The de source remains unchanged. Calculate the temperature coefficient of copper.
Calculate DC Voltages on each terminal of the FETS or MOSFETS. +15 V -10 V +12 V 8 mA 6 mA R 1.0 kN R 10 k2 3 mA 1.5 kn 1.0 kf. RG 10 M2 Re 10 MN Rs 330 N R2 4.7 kf (b) (c)
Let's Try (Evaluation) Directions: Complete the table by supplying the needed information. In some parts, you need to provide the color bands and in some other parts, you have to give the resistance and tolerance values. Band A Band B Band C Band D Resistance Tolerance Yellow Violet Red Silver 2.2 MQ 10 % 4 Orange Orange Black Gold 910 Q 5 % Green Red Green No color 10000 Q 20%
Design an ohm-volt-ampere scale with the following characteristics Voltage 5 25 100 Volt ranges current 10 100 500 milliampere ranges ranges of resistance 20 200 2000 middle of the step Ohm in the E=3v Rm=500 Ohm Ifsd=50 Micro ampere Draw the measurement chart with the reading board, provided that the scale has two main keys, one to choose the type of scale and the other to choose the range
A 1000-VA, 230/115-V transformer has been tested to determine its equivalent cir- cuit. The results of the tests are shown below. Open-circuit test (on secondary side) Short-circuit test (on primary side) Voc = 115 V Vsc = 17.1 V %3D %3D Isc 8.7 A Psc loc =0.11 A Poc = 3.9 W = 38.1 W (a) Find the equivalent circuit of this transformer referred to the low-voltage side of the transformer. (b) Find the transformer's voltage regulation at rated conditions and (1) 0.8 PF lag- ging, (2) 1.0 PF, (3) 0.8 PF leading. (c) Determine the transformer's efficiency at rated conditions and 0.8 PF lagging.
Given data: I1=0.06 I2=0.25 I3=0.42 I4=0.74 I5=0.49 I6=0.32 R1=25 R2=45 R3=10 R4=15 R5=20 R6=40 E1=10, E2=35
A scientist working under emergency conditions at a jungle based lab realizes that her primitive radio has shorted in the rain and burned out a resister. She wants to match the original resister of 2.50 Ohms but believes that a resistance between 2.25 - 2.75 Ohms would be sufficient. All she has to work with is a spool of fine lead soldering wire and some scrap equipment. a) The wire has a diameter of 1.5 mm and the resistivity of lead is 22*10-8Ohm-meters. How much lead wire would she need to make the resister? b). Looking around the lab she is able to scavenge two 3.5 ohm and one 1.0 ohm resisters from old equipment. Using these three resisters how close can she come to building a 2.50 ohm resister? Explain the optimal configuration and calculate the equivalent resistance.
3 pls show the give,. formula then substituion. thanks!