The diagram illustrates the operation of a fuel pump in an automobile, which relies on the reciprocating motion of the rocker arm ABC. This arm is pinned at point B and is spring-loaded at points A and D.The vertical force applied to the rocker arm at point A is \( F_A = 50 \, \text{N} \), and at point C, it is \( F_C = 150 \, \text{N} \).The diagram shows the mechanical setup with the following details:- The rocker arm ABC pivots around point B.- A spring is positioned at an angle of 30°.- Distance measurements are given as follows: - 50 mm from point A to B - 10 mm from point B to D - 20 mm from point B to CThe task is to determine the magnitude of the force at point B when the smooth cam C is in the depicted position.

T 30°- 50 mm 20 mm-| 10 mm The operation of the fuel pump for an automobile depends on the reciprocating action of the rocker arm ABC, which is pinned at B and is spring loaded at A and D. The vertical force acting on the rocker arm at A is FA = 50N, and at C it is Fc = 150N. When the smooth cam C is in the position shown, determine the magnitude of the force at B

T 30°- 50 mm 20 mm-| 10 mm The operation of the fuel pump for an automobile depends on the reciprocating action of the rocker arm ABC, which is pinned at B and is spring loaded at A and D. The vertical force acting on the rocker arm at A is FA = 50N, and at C it is Fc = 150N. When the smooth cam C is in the position shown, determine the magnitude of the force at B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the components of the reaction force at point O for the frame shown below. The magnitude of the tension in the cable is 750 lb. The work must be clear and well-organized to receive full credit. All work must be shown to receive full credit. x 0.8 ft 1.6 ft Z 1.5 ft B y 35° 0.9 ft
C Aroller of weight 500 N has a radius of 120 mm and is pulled over a step of height 60 mm by a horizontal force P. The magnitude of Pto just start the roller over the step is r= 120 mm B 60 mm
For what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A be zero? If a couple of that same magnitude M were applied in a counterclockwise direction, what would be the value of Ax? Answers: M= A Ax= i i -2.4° 170 lb L--x -2.4 B M 1.9' 64° lb-ft lb 1.9' C
Four forces are exerted on the eyebolt as shown. If the net effect on the bolt is a direct pull of 610 lb in the y-direction, determine the necessary values of T and e. Assume F₁ = 315 lb, F₂ = 295 lb, F3 = 390 lb, d = 30° F₁ Answers: T = e= i i lb O T Ф
Determine the magnitude of the horizontal force F and the support reactions at pin A.If the cord CB can sustain a maximum load of 1500N.
SKIP IF YOU ALREADY DID THIS OR ELSE DOWNVOTE
Q1) A man is pulling a spring of stiffness coefficient 8 Ib/in by his hand with the entire arm held horizontally rotating about shoulder joint O; this force acts at the 21° angle is shown. Determine the force exerted by the deltoid muscle on the upper arm at A and x- and y- components of the force reaction at the shoulder joint. The weight of the upper arm Wu = 4.1 Ib, the weight of the lower arm W1 2.4 Ib, and the weight of the hand WH= 0.9 Ib; all these weights act at the locations shown in the figure. the spring extended 1 in only as shown in figure 1. A tensile force in the deltoid muscle prevents the arm from A- 8 Ibin Equilibrium x-1 in Deltoid muscle Fo A YW, YW -5.2 16.5 25.4 Figure 1
The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 820 N, determine the n- and t- components of this force acting on point A of the bar. 2.0 m B Answers: Tn= i Tt= i Attempts: 0 of 4 used Submit Answer -1.5 m Save for Later 63⁰ Z Z N N
- The unifom bar OC of lmgth L md mass (m) pivots freely about a horizontal axis through O. If the spring of modulusk is unstretched when C is coincident with A, detennine the tension T roquired to hold the bar in the position shown. The diameter of the small pulley at D| is negligible. L/2 L/2
End B of the uniform 2.7-kg bar AB is connected to a small roller that moves in a horizontal slot. The other end of the bar is pinned to the homogeneous 1.8-kg disk that rolls without slipping on the vertical surface. The spring attached to A has a free length of 0.3 m and a stiffness of 58 N/m. After the system is becomes horizontal. Determine the magnitude of the force P that acts on the bar at B. 2.1 m 0.24 m 0.9 m www 1.8 kg 1.5 m 2.7 kg P
The uniform bar OC of lenght L pivots freely about a horizontal axis through O. If the sping of modulus k is unstretched when C is coincident with A, determine de tensión T required to hold the bar in the 45° position shown. The diameter of the small pulley at D is negligible. draw the free body diagram.
4/16 The rectangular frame is composed of four perim- eter two-force members and two cables AC and BD which are incapable of supporting compression. Determine the forces in all members due to the load L in position (a) and then in position (b). L 3d A D (a) B L 4d с (6)