Switch Type Rotary Switch (6 way) Symbol Voltage Current No. of pins Contact& Insulation Resistance Pole throw configuration

Q: Q1: For the network of Figure below, VDD= 9 V. Determine: (а) ID. (b) VS and VDS. (c) VG and VGS.…

A:

Q: In MCB's what is the difference between type B, C, D. Which is better to use if you have an arc…

A: Type B MCB'S-- A type B trips when current is 3 to 5 times of rated current with an operating time…

Q: A step up chopper has an input of 200 volts and output of 250 volts. The blocking period is each…

A:

Q: Problem 5. Find the range of parameters g and r in which the circuits below are stable: a) о b) gVc…

A:

Q: c) Explain the reason for the speedup and slow down of an electron in atomic orbit placed in…

A: In the magnetic field, there are varies changes in the election speed in orbit. The speed of the…

Q: what is the use of DC/DC tension converter DC/DC booster MT3608

A: Types of mostly used DC DC Converter Step up Converter ( Boost converter) Step Down Converter (…

Q: 2. Which of the symbols in Figure A6 represents a circuit breaker with thermal overload protection?…

A: The fundamental task of a circuit breaker is to react to the relay trip signal and  operate…

Q: alculate the maximum force that should be applied via a pulling eye to a 70 mm2, 3-core copper…

A: Given, The maximum force applied via a pulling eye to a 70 mm2, 3 core copper cable, For copper…

Q: what are charging and discharging time of this circuit.

A: Given circuit is -

Q: In an On-Off AC Voltage controller, the ON time is 50 cycles and duty cycle is 0.25. The OFF time…

A: Let M be the number of on cycles and N be number of off cycles. Duty cycle=no.on cyclesno.on…

Q: Question 1 a. Derive the following speed equations: i. ii. ω 3 V, Kφ Ra Ta Kφ Κφ V Kφ Κ$ R a la

A: The above speed equations represent the speed equation of a DC motor Basic Theory: EMF equation(Ea)…

Q: An AC ammeter is connected in series with the primary winding of T1. What is the expected current…

A: The output RMS value of output voltage is as=8.48 voltsThe RMS current measured by the ammeter

Q: 19. Identify the response time of a meter. a. Time taken by output to reach final constant value…

A: Identify the response time of a meter. It's depend on the parameter.

Q: Find i in the network using superposition. 5Ω 10 Ω 2 A 5Ω 4Ω 20 V

A: This theorem is used to find current in any particular branch. To apply this minimum 2 sources are…

Q: A snubber circuit has snubber time constant (10 msec), voltage source (10 kV), discharge current of…

A: Given data, Time constant,τ= 10 msec Voltage source V = 10 KV = 10000 V Discharging current is,…

Q: proximately, how long does it take the circuit to have a current near 5A upon closing of the ritch?…

A:

Q: Fill in the blanks: Given the model for position control system, find the value for K1 and K2 so…

A: Given, Position control system is Peak time,tp = 0.5s %overshoot = 3% We need to determine values…

Q: lain the operation of a full subtractor with necessary diagrams. What is the difference between half…

A: Full Subtractor : It is is a combinational circuit that perform subtractor it consist three bits. It…

Q: Rotary switch (4 way)

A: Rotary switches are available in 1 pole, 2 poles, 3 poles, and 4 poles popular with 1 phase, 2…

Q: Design a clamper to perform the function indicated Vị Vo +16 V Ideal diodes 20 V Vi Design -4 V -20…

A: In this question,  Design a clamper to perform the function indicated.  Output voltage waveform and…

Q: The principle operation of LVDT is based on the variation of Select one a. Self inductance b.…

A: Right Answer option C.Mutual Inductance

Q: An inductive load of 100 Ohm and 200mH connected in series to thyristor supplied by 200V dc source.…

A: Given information is that an inductive load is connected in series to thyristor. The supply voltage…

Q: Enumerate the procedure in making a double-threaded screws

A: Having two screw threads instead of one; said of a screw in which the pitch is equal to twice the…

Q: a. A simple DC circuit is shown in Figure 4. If ix=10A, find v1 and iy If v1=6V, find ix and iy. i.…

A: The solution can be achieved as follows.

Q: A flat circular coil with 40 loops of wire has a diameter of 32 cm. What current must flow in its…

A: The magnetic field at the center of the circular loop is given by the expression as shown below:…

Q: A snubber protection circuit has snubber time constant (5msec), voltage source (5kV), discharge…

A: Given a snubber protection circuit has, Time constant, τ=5 msec Voltage source, V = 5 kV Discharging…

Q: Impact of different type of governors on Transient stability

A: Introduction: The Power System Stability of an electricity system is its ability to return to…

Q: A snubber circuit has snubber time constant (10 msec), voltage source (10 kV), discharge current of…

A: When a switching device is in it's reverse recovery states, various charge carriers recombine. This…

Q: 2. A DSB-SC AM signal is modulated by the signal m (t) = 2cos2000nt + cos6000nt. The modulated…

A:

Q: what is ripple ? how to minimize the rippl , draw the circuit and show ??

A: It is one of the important parameter which is taken into consideration while designing any power…

Q: explain the principles of SMAW welding. b) explain the output slope of power source for SMAW c)…

A: Introduction: Welding is a fabrication method that involves fusing two or more pieces together using…

Winding and Constructions

Alternating Current (AC) winding is generally of the 3-phase type due to the inherent advantages of the 3-phase machine. Armature coils must be connected to the yield balance (equivalent in magnitude and 2/3 of the series phase difference of the rod) 3-phase electromotive forces (emf). The armature should be divided into step-bands to start with slots around the perimeter.In the construction of AC machines, the frame is used as an external protective shield to protect it from environmental conditions. The frame also serves as the outer perimeter, allowing the interior to be easily placed. The static state section of the devices is the stator winding attached stator.