SW1 a SW2 0 SW3 o SW4 LSB O 1 2 I 4 5 9 10 112 1 13 th th FI A from logic switch A 31 6 T 11 1 81 L1 L2 L3 L4 INPUTS SW2 SW3 SW4 SW1 SW2 0 1 1 0 0 1 0 0 0 1 1 1 0 1 0 1 Logic circuit function: L1 OUTPUTS A NORMAL L2 L3 L4 A in UP position L2 L3 L1 The inputs will come from the data switches. Observe the outputs on the LED indicators. Switch SW4 and LED indicator L4 can be considered be the LSB of the four bit binary word input and output. Set all of the input data switches to the binary 0 state. Observe the output state and record your output value in Table Next, place the logic switch A in the up (ON) position. Observe the output indicators and record the state presented in Table For each of the input states recorded in Table 3-3, record the output states with the logic switch A in its normal position (off) and in its up position (on). Study the results in Table. Using this information and the circuit in Figure as well as the results of your previous steps, determine the function of this circuit. L4

SW1 a SW2 0 SW3 o SW4 LSB O 1 2 I 4 5 9 10 112 1 13 th th FI A from logic switch A 31 6 T 11 1 81 L1 L2 L3 L4 INPUTS SW2 SW3 SW4 SW1 SW2 0 1 1 0 0 1 0 0 0 1 1 1 0 1 0 1 Logic circuit function: L1 OUTPUTS A NORMAL L2 L3 L4 A in UP position L2 L3 L1 The inputs will come from the data switches. Observe the outputs on the LED indicators. Switch SW4 and LED indicator L4 can be considered be the LSB of the four bit binary word input and output. Set all of the input data switches to the binary 0 state. Observe the output state and record your output value in Table Next, place the logic switch A in the up (ON) position. Observe the output indicators and record the state presented in Table For each of the input states recorded in Table 3-3, record the output states with the logic switch A in its normal position (off) and in its up position (on). Study the results in Table. Using this information and the circuit in Figure as well as the results of your previous steps, determine the function of this circuit. L4

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An IC with two-input logic gate produce a output as LOW, only when all of the inputs are HIGH is O IC 7408 O IC 7400 O IC 7432 O IC 7486
Find the logic function Z for the diagram shown in the figure B2. 1 0, 2x1 MUX B I1 A Figure B2
Find the simplified sum-of-products representation of the function from the Karnaugh map shown in Figure below. Draw logic circuit. (Note that x is the don't care term) A-B 00 C-D 00 0 01 11 10 01 1 1 11 1 10 1
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
E1
Discussion: 1. Simplify the following logical expression and implement them using suitable logic gates. a F = E2,4,6,10,14 b. F I12,3,6 2 Determine whether or not the following equalities correct: a. A+B.C+Ã•C = B C b. B(AO c) +BČ+ ACBOC) = AC 3. Convert the following expressions to SOP forms: a. (A +B.C) B b. (A + C)(Ã B Č+A C D) * 4. Write a Boolean expression for the following statement: Fisa "I" if A, B&C are all l's or if only two of the variable is a"0". 5. Find F %3D T IT D
None
Example: Neglect the base currents. (a) What logic function is performed by this circuit? (b) What are the logic 1 and logic 0 values of Vo at the output? (c) When VA logic 0 for one of the two inputs, determine i, i ich ic and V. (d) Repeat part (c) when all inputs are logic 1. 2.6k2 Va iz 5V 1.2ΚΩ Q₁ Q₂ 1.6V Q2 Vo 0.8kQ
Q2/A. Design a logic circuit that perform the following Boolean function, use 4-to-1 multiplexer and other logic gates you may need in the design. Use Shannor expansion 21 18 31 f(A, B, C, D, E) = ABCDE + ABCDE + ABCDE + ABCDE %3D l68421 B. Design 8-bit Adder/Subtracter using 4-bit Adder and 2-to-1 multiplexers other logic gates you may need in the design.
1. For the logic diagram shown in Figure Q1, Obtain the logic functions for S and T. Prove that S and T functions are complement of full adder. a. b. Do %$4 NORT & 2 to 4 decoder E Y1 2 to 4 decoder NOR2 NOR3O Figure QI rotus %23
Draw the F1 and F2 outputs of the above logic circuit only with OR NOT gates and A, B, C, D independent logic variables in the Proteus program.
answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC)* When input is 0000 that means tank is empty.* When input is 1111 that means tank is full.* When input is below 5, that means water level is low.* So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light(by setting an output L to 1) when the water level drops below level 5.