d) For the given circun Fill the truth table and identify the type of logic gate For the transistor write ON or OFF Vout should be 0 or VoD VA | VB Q1 Q2 Q3 Q4 Vout VDD VDD Vop VoD

Q: The slip compensation function causes the drive to __________ the frequency of its output when the…

A: Full the given blank.  The slip compensation function causes the drive to __________ the frequency…

Q: Define and draw unit circle. What is the significance of unit circle for system analysis?

A: to draw and define unit circle significance of unit circle for system analysis

Q: For a system consist from 3 buses and bus 1 is the slack bus. The data of the system are:- 0.25 Ybus…

A: In this question we need to find a voltage of bus 3 after two iteration

Q: MPCB is used to protect the motor from over load. Select one: True False

A:

Q: Total demand on any power generating station is equal to sum of generator inputs sum of generator…

A: Ans- (b) sum of generator output.

Q: 11. What affects the angle of lead? (DC GENERATOR QUESTION)

A: It is asked that whet affects the angle of lead. We have given the explanation by using some…

Q: The duration of the load curve can be extended for any period time

A:

Q: 4.1Two synchronous generators need to be connected in parallel to supply a load of 10 MW.  The first…

A: The solution is given below

Q: Total demand on any power generating station is equal to sum of generator inputs sum of generator…

A: Total demand in any power system is the sum of generator outputs .

Q: • What is the length of PN sequence generator of DB20? What is the PN Sequence of the DB20.

A: PN sequence stands for Pseudo Noise sequence .

Q: Why 'during fault' do we use the transferred reactance of (X_12) 1.8 to calculate P2 Max. Why do we…

A: The question is about calculating net impedance during fault.

Q: write conclusion about  Single Line Diagrams  residential and industrial power systems. please…

A: It is asked to write a conclusion about  Single Line Diagrams  residential and industrial power…

Q: Load duration curve Hours 0 500 2000 4500 6000 8760 Mw 50 Load 50 35 30 20 |15 there are two (2) -40…

A: Rating of each generator = 40 MW Energy = power X time Plant load factor = Actual energy generated…

Q: Explain about PI Control of the Integrating Pumped Tank Process

A: The main objective for PI control of integrating pumped tank process is to maintain liquid level at…

Q: 2. Compute carry and overflow flags in the following table. Carry Overflow Operation 0100 0110 0101…

A:

Q: Three synchronous generator are connected in parallel to a an infinite s. G1 only provides active…

A:

Q: For a system consist from 3 buses and bus 1 is the slack bus. The data of the system are:- 0.25 -0.2…

A:

Q: The power supplied to an infinite bus system is 0.6 times of the maximum power transferred. What is…

A: Given, Power supplied, P=0.6Pmax

Q: Increasing will cause the rise time to decrease and reduces steady state error, but increases…

A:

Q: Voltage (V) 120 100 80 40 20 0 0 30 Time (us) The load must be predominantly resistive. The average…

A: Peak current is 2A.Peak Voltage is 100V.Both waveforms are triangular.

Q: List down 3 main parts of DC generator

A: DC GENERATOR: When the local grid is down, independent equipment called electrical generators can…

Q: Power flow analysis using Newton-Raphson method occupies memory of the computer. O Limited O Less O…

A: Newton - Raphson method is used to solve load flow problems. It uses Tailor's series and partial…

Q: 1. 2. 3. (1) 32- 3 28 26 24- 22 2- 18 16 14 12- 1- 16- 04- 02 15 t(seconds) R the overshoot in %:…

A: % over shoot=[(value at 1st maxima- final value)/final value]×100 Peak time is the time taken by the…

Q: QUESTION 3 A type 1 system can track which of the following input signals with 0 steady-state error?…

A: Question 3 The steady-state error for a unit step function is given as:  ess=11+kpkp=positional…

Q: Problem_#03] For the ripple counter below, complete the timing diagram for eight clock pulses. HIGH…

A:

Q: b) A1000 MW turbine generated 648 MWh during 30 da What would is capacity factor be?

A: In this question we will find capacity factor of turbine...

Q: Shunt and undercompound generators are highly unstable for parallel operation compared to…

A: Answer is FALSE.         Shunt generators are most suited for stable parallel operation because of…

Q: List down 3 main parts of DC generator

A: DC GENERATOR: When the local grid is down, independent equipment called electrical generators can…

Q: Differentiate between a cumulative compound DC generator and a differential compound DC generator.

A:

Q: Calculate the availability if a generator unit whose failure rate is given as 0.0011failures per…

A: In this question we need to find a availability of a genrator for the given condition.

Q: Voltage fluctuations will be there for consumers at distant end in Ring feeder O Radial feeder O…

A: In this question we will write in which feeder voltage fluctuations is there at consumers…

Q: 1. Rate of convergence of the Newton-Raphson method is generally O Linear O Cubic

A: Newton's Raphson method, also known as the Newton's method, named after Isaac Newton and Joseph…

Q: Determine the range of stability using the Routh criterion for the system below? R(s) SÉs +4} (s +6}

A: Fig: Given control system  Calculate transfer function of the given…

Q: Question 4 In case of N-R method of power flow solution at the generator bus one column and one row…

A: 4) Newton- Raphson method of power flow solution at the generator bus

Q: Can we used information signal has frequency 500 Hz? why? at AM-SSB

A: The solution is given below

Q: Which of the following statement is not correct regarding the circular shift of a 4-point…

A: circular shift of a 4 point discrete time sequence will repeate after 4,8,12 time unit shift and its…

Q: A11 e generators are classified according to the methods of their field excitation. (TRUE/FALSE)

A:

Q: Quiz: An alternating current of frequancysoH has makimum Value of ( 20A).write the instantanous…

A: Given frequency is not clear, so i am taking f = 60 Hz. Given data,

Q: Closed-loop system is strongly influenced by the presence of disturbances, and it needs calibration…

A: Introduction Closed-loop system: A closed-loop system is a type of control system that utilizes a…

Q: Q.5 Explain why are some parts of electrical machines laminated? [CO-1; CO-3]

A: Electrical machines can be either generator or motors. They can be either Ac machines or DC…