SW The composite bar shown in Fig. P-273 is firmly attached to unyielding supports. An axial force P = 50 kips is applied at 60°F. Compute the stress in each material at 120°F. Assume a = 6.5 × 10- 6 in/(in-°F) for steel and 12.8 x 10-6 in/(in.°F) for aluminum.

SW The composite bar shown in Fig. P-273 is firmly attached to unyielding supports. An axial force P = 50 kips is applied at 60°F. Compute the stress in each material at 120°F. Assume a = 6.5 × 10- 6 in/(in-°F) for steel and 12.8 x 10-6 in/(in.°F) for aluminum.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P Strain gage D E H b. Answer: P = i 29254 N
1. Find the properties of equal-leg angle bar 150 x 50 x 6.0 in metric. 2. Find the full section properties of LC shapes steel bar 100 x 50 x 15 x 3.0 in metric. 3. A stress that lies between the proportional limit and the upper yield point of a steel. What is 5 and 5 Show the relationship uring a graph of mild structural stool
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 με is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
A composite beam is made of two brass [E = 97 GPa] plates bonded to an aluminum [E = 72 GPa] bar, as shown. The beam is subjected to a bending moment of 2420 N-m acting about the z axis. Assume b=64 mm, d1=36 mm, d2=13 mm. Determine: (a) the maximum bending stresses opy,Gal in the brass plates and the aluminum bar. (b) the stress in the brass obrj at the joints where the two materials are bonded together. Brass (2) d2 Aluminum (1) Brass (2) dz b Answers: (a) obr = i MPa, oal = i MPа. (b) Obrj MPa.
A small aluminum alloy [E = 80 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 430 µɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P ЗР Strain gage d D E H Answer: P = i
A small aluminum alloy [E= 77 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 160 mm. The cross- sectional dimensions of the tee shape are b= 22 mm, d = 33 mm, and t= 4 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 410 uɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? %3D %3D %3D 3P Strain gage E Answer:
A composite beam is made of two brass [E = 120 GPa] bars bonded to two aluminum [E = 70 GPa] bars, as shown. The beam is subjected to a bending moment of 400 N-m acting about the z axis. Using a = 15 mm, b = 100 mm, c = 30 mm, and d = 65 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Aluminum y Brass Aluminum b Brass C a d
A composite beam is made of two brass [E = 120 GPa] bars bonded to two aluminum [E = 73 GPa] bars, as shown. The beam is subjected to a bending moment of 445 N-m acting about the z axis. Using a = 15 mm, b = 125 mm, c = 30 mm, and d = 75 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Z Aluminum C Aluminum Answers: (a) Ogl Brass (b) Obr= i i b Brass a MPa MPa
QU A composite beam is fabricated by bonding a steel bar and a brass bar and is subjected to the bending moment M = 200 N-m. Determine the maximum bending stress in the brass and steel. Given: E, =200 GPa, E, = 100 GPa Brass 20 }o | Jakrtal
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
A composite beam is made of two brass [E = 112 GPa] bars bonded to two aluminum [E = 69 GPa] bars, as shown. The beam is subjected to a bending moment of 350 N-m acting about the z axis. Using a = 15 mm, b = 115 mm, c = 25 mm, and d = 65 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Z Aluminum с Aluminum Answers: (a) Jal= (b) Obr= Brass i y i b Brass a a MPa MPa