Suppose we have a uniform beam that is 2.92 metres long has a flexural rigidity of 30254Nm². N Find the deflection of the beam in millimetres if the beam is under a load of f(x) = 6.88(x + 1.3468) (3.42 — x)- and is supported with a fixed support on the left end, and a simple support on the right end. Fill out the table below with your answers. m Deflection (mm) x-coordinate x = 0.53 x = 1.08 y(x) = | y(x) = y(x) = x = 1.37 x = 2.16 y(x) = x = 2.66 y(x) = | Enter as many decimal places as your calculator allows (8 to 10). Your answer must be within +0.0005 of the correct answer to be considered correct.

Suppose we have a uniform beam that is 2.92 metres long has a flexural rigidity of 30254Nm². N Find the deflection of the beam in millimetres if the beam is under a load of f(x) = 6.88(x + 1.3468) (3.42 — x)- and is supported with a fixed support on the left end, and a simple support on the right end. Fill out the table below with your answers. m Deflection (mm) x-coordinate x = 0.53 x = 1.08 y(x) = | y(x) = y(x) = x = 1.37 x = 2.16 y(x) = x = 2.66 y(x) = | Enter as many decimal places as your calculator allows (8 to 10). Your answer must be within +0.0005 of the correct answer to be considered correct.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular beam carries a triangular load "w" as shown in the figure. Determine the following unknowns if the modulus of elasticity is 160GPa and the maximum deflection is -0.63254616477273mm. BEAM'S DIMENSION: Width = 110mm , Height = 480mm NOTE: L = 3m Solve the maximum moment of the beam. Answer for part 1 kN-m Determine the shear at midspan.
A truss carries a concentrated load at points B, E, F, and Gas shown in the figure below. Using unit load method, determine the deflection of the following point. All members of the truss have a circular cross-section: Top Chord has a diameter of 29mm; Bottom chord has a diameter of 44mm; Web member has a diameter of 13mm. USE E=125GPA. 2P 2P G E 300 60° 60° 60° 60, 300 A В D ЗР 4m 4m 4m If the reaction of point D is 273.32531754731kN, determine the value of "P". Determine the vertical deflection of point F. (NOTE: Put a negative sign if the direction is going down, otherwise don't put any sign) Determine the horizontal deflection of point D. (NOTE: Put a negative sign if the direction is going to the left, otherwise don't put any sign) Determine the vertical deflection of point E. (NOTE: Put a negative sign if the direction is going down, otherwise don't put any sign) Determine the force acting at member BF due to applied force. (NOTE: Put a negative sign if your answer is compressive…
Analyze the beam shown in Figure using flexibility method of analysis. Take EI as constant.
Problem Solving. 1. The maximum bending moment for a 4 meters freely supported beam has been found to be 15 kN-m. If the allowable bending stress is 9 MPa, design the beam with respect to bending. Use E = 12,000 MPa a. a. Investigate if the computed dimensions will not exceed the allowable shearing stress of 0.90 MPa. b. Investigate if the computed dimensions will not exceed the allowable deflection of L/360. w (kN/m) 4m
2. A uniform, simply supported beam, is loaded as shown in Figure 2. Using singularity functions, determine an expression for the bending moment at any point along the beam. Hence, determine the slope of the beam at point, A, and the deflection of the beam at point, B. The bending stiffness of the beam is 3200 Nm². 320 N 200 N/m 1.2m 0.6m Figure 2 2 A 0.4m X * B D
Hw1: For the simply supported beam shown in Figure, determine the maximum deflection due to the applied load. The flexural rigidity of the beam is El= 7x106 kip.in². V₁ = 20 kips a = 12 ft 1 = 18 ft Answer: ymax = -0.129 ft downward W = 60 kips b = 6 ft 2 V₂ = 40 kips
Note: careful with given dimensions. Give me right solution with clear calculations step by step. Don't copy from other experts solution
Part C
The structure shown in Figure is subjected by a force P =253 N at central point. Determine the absolute vertical reaction force at A. Solve the problem by assigning 100 beam elements along the path AB. Consider, elastic modulus E = 200 GPa, poisson's ratio v = 0.3, radius R = 500 mm. The ring has a circular cross sectional area with diameter of 10 mm. (The answer unit should be in N). Acceptable error: 4% 1A Yanıt:
= == 1 in.2, 10,000 lb. Each bar of the simple truss shown in Fig. 6.5a has cross-sectional area A; and modulus of elasticity E 10(106) psi; a = 10 √2 in., and P Calculate the horizontal deflection 8, of joint C. = Aα C P a a B
A beam supported by three identical springs at points A,B,C (see figure). Given that flexural of rigidity of the beam, EI= 2.029X1011 N.mm2 ; spring constant,k = 1471.5N/mm, w=116N/mm All dimensions are in mm. 1. What is the reaction for at point A,B and C? 2. What is the deflection at point B? 3. Please draw shear-force and bending moment diagram.
A simply supported beam is subject to a downwards uniform distributed load, w, as shown below. B A uniform distributed load, w L1 L2 The cross-section of the beam is constant with second moment of area I = 3750 mm², and Young's elastic modulus is E = 200 GPa. The distributed load has magnitude w = 220 N/m. If Point B is distance L₁ (Point C), calculate: the downwards vertical deflection at Point B: C C 435 mm from the left end (Point A) and distance L2 = 385 mm from the right end Round your answer to 3 significant figures. X [Units: mm]