Suppose two hosts (Host-A and Host-B) are connected through a shared Ethernet bus of 1 Mbps. The distance between two nodes is 5 meters. The signal propagation speed over physical media is 2.5 x 10^5 meters/second. B Bus Topology a) Compute the propagation delay in this case. b) What will be the propagation delay for a shared bus of 10 Mbps instead? c) Suppose both hosts sense idle channel at the same time and starts transmission. Will it result in collision (yes or no)? Explain. d) If yes, How much time is needed to detect this collision at Host-A? Show working. e) If yes, How much time is needed to detect this collision at Host-B? Show working.

Suppose two hosts (Host-A and Host-B) are connected through a shared Ethernet bus of 1 Mbps. The distance between two nodes is 5 meters. The signal propagation speed over physical media is 2.5 x 10^5 meters/second. B Bus Topology a) Compute the propagation delay in this case. b) What will be the propagation delay for a shared bus of 10 Mbps instead? c) Suppose both hosts sense idle channel at the same time and starts transmission. Will it result in collision (yes or no)? Explain. d) If yes, How much time is needed to detect this collision at Host-A? Show working. e) If yes, How much time is needed to detect this collision at Host-B? Show working.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Suppose hosts A and B are connected by a link. Host A continuously transmits the current time from a high-precision clock, at a regular rate, fast enough to consume all the available bandwidth. Host B reads these time values and writes them each paired with its own time from a local clock synchronized with A's. Give qualitative examples of B's output assuming the link has (a) High bandwidth, high latency, low jitter. (b) Low bandwidth, high latency, high jitter. (c) High bandwidth, low latency, low jitter, occasional lost data. For example, a link with zero jitter, a bandwidth high enough to write on every other clock tick, and a latency of 1 tick might yield something like (0000,0001), (0002, 0003), (0004, 0005).
Suppose Ethernet physical addresses are chosen at random (using true random bits). (a) What is the probability that on a 1024-host network, two addresses will be the same? (b) What is the probability that the above event will occur on one or more of 220 networks? (c) What is the probability that, of the 230 hosts in all the networks of (b), some pair has the same address? Hint: The calculation for (a) and (c) is a variant of that used in solving the so-called Birthday Problem: Given N people, what is the probability that two of their birthdays (addresses) will be the same? The second person has probability 1-3 of having a 365 different birthday from the first, the third has probability 1 365 of having a different birthday from the first two, and so on. The probability that all birthdays are different is thus 2 (1-365)×(1-325) × × (1-N5¹) X X 365 which for smallish N is about 1+2+ 1 · + (N − 1) 365 ...
urgent
The distance from earth to a distant planet is approximately 9 x 10^10 m. What is the channel utilization if a stop-and-wait protocol is used for frame transmission on a 64 Mbps point-to-point link? Assume that the frame size is 32 KB and the speed of light is 3 × 10^8 m/s.
basic data link layer principles (e.g. PPP if modems, maximum frame size in byte, maximum header size, CSMA/CA or CSMA/CD media-access control if any, etc): Your answer
A CSMA/CD LAN has minimum frame size 100 bytes and is running at 100 Mbps. The signal speed in the cable is 200,000 km/sec and the delay generated by the repeaters can be ignored. What is the maximum size the bus can have? (Note: ignore signal attenuation).
Explain the types of addresses (identifiers) and how many addresses (i.e., the number of addresses used to identify the start and end points; what are they called in general) are used in each of the following layers? Provide one example (i.e., write the address in standard format) for each type of addresses. - Network layer - Data link layer If there is a single path between the source host and the destination host, do we need a router between the two hosts?
1. It is known that the MAC address is the only address that is used in order to communicate and reach to the destination in the local network. Study the figure below carefully and then answer the following question: Suppose that a data (shown in the figure) has arrived to the router A. The ARP table for Router A is as shown in the figure below. Discuss the necessary steps that are needed for the Router A to prepare the frame for the final hop. MAC src: 74-29-9C-E8-FF-55 ARP Table MAC dest: E6-E9-00-17-BB-4B IP src: 11.11.11.11 IP MAC TTL IP dest: 22.22.22.22 11.11.11.11 74-29-9C-E8-FF-55 22.22.22.11 88-B2-2F-54-1A-OF 20 minutes 18 minutes 11.11.11.11 22.22.22.22 74-29-9C-E8-FF-55 49-BD-D2-C7-56-2A Router A 11.11.11.10 22.22.22.20 11.11.11.22 22.22.22.11 E6-E9-00-17-BB-4B 1A-23-F9-CD-06-9B cC-49-DE-DO-AB-7D 88-B2-2F-54-1A-OF
In a broadcast architecture, why is an ARP query being sent? Why is an ARP response sent in a frame with a destination's MAC address?
Calculate the delay x bandwidth product for the following links. Use one-way delay, measured from first bit sent to first bit received. (a) 100-Mbps Ethernet with a delay of 10 μs. (b) 100-Mbps Ethernet with a single store-and-forward switch like that of Exercise 16(b), packet size of 12,000 bits, and 10 μs per link propagation delay. (c) 1.5-Mbps T1 link, with a transcontinental one-way delay of 50 ms. (d) 1.5-Mbps T1 link between two groundstations communicating via a satellite in geosynchronous orbit, 35,900 km high. The only delay is speed-of-light propagation delay from Earth to the satellite and back.
Assume there is a 1 Mbps shared connection (e.g. Ethernet bus). How long (in microseconds) does it take to send a 1000-bit frame over this link?
Consider the Ethernet networks shown in the below exhibit to answer the following questions. Fa0 Fal PC3 PCO Fa0/1 Fa0/0 Fa0/3 Etho/D/0 Fa0/2 s1 Fa0/1 R1 Fa0 Fa0/0 Fa0/1 PC1 R2 Fa0/1 Fa0/3 S2 Fa0 PC2 The network interface settings of POs are: Logical Address Physical Address PCO 192.168.2.2 0060.5032.9A15 PC1 192.168.2.3 o001.6363.6BAA PC2 192.168.3.2 O0EO.F9A1.0864 PC3 192.168.0.2 0001.0935.08C3 The network interface settings of routers are: Logical Address Physical Address R1-Fa0/0 192.168.0.1 0004.9A31.0501 R1-Fa0/1 192.168.1.1 0004.9A31.0502 R1-Etho/0/0 192.168.2.1 0060.2F70.0D9B R2-Fa0/0 192.168.1.2 0002.1641.6301 R2-Fa0/1 192.168.3.1 0002.1641.6302 Suppose that the switching table in the S1 contains the following contents: Fa0/1 Fa0/2 Fa0/3 Fa0/4 Open Fa0/5 Fa0/6 Fa0/7 Fa0/8 Open Open Open Open If a frame with source MAC address 001.6363.6BAA and destination MAC address 0060.5032.9A15 is received at the switch, at which port does the frame arrive? Which port(s) will the frame go…