D1 Suppose the spatial multiparticle wavefunction for 5 identical fermionsY(T₁, T2, T3, T4, T5)1,is written in terms of the single particle states ¡(7,) for i ɛ{a, b, c, d, e}and j &{1,2,3,4,5}.How many terms exist in such an expansion?

Given,For a single particle,The wavefunction in the state is given by,ψir→jHere,i ∈a, b, c, d, eandj…

Suppose the spatial multiparticle wavefunction for 5 identical fermions Y(T1, T2, T3, T4, T5) is written in terms of the single particle states ¡(77) for i ɛ{a, b, c, d, e} and j &{1,2,3,4,5}. How many terms exist in such an expansion?

Suppose the spatial multiparticle wavefunction for 5 identical fermions Y(T1, T2, T3, T4, T5) is written in terms of the single particle states ¡(77) for i ɛ{a, b, c, d, e} and j &{1,2,3,4,5}. How many terms exist in such an expansion?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Hello Sir.Good Night. I have a question in my home work related Control System Lesson. The following below is my question.Please advise, Thank you so much.
Q1) In a box there are 100 resistors having resistance and tolerance as shown in the following table. Let a resistor be selected from the box and assume each resistor has the same likelihood of being chosen. Define three events A as draw a 472 resistor, B as draw a resistor with 5% tolerance and C as draw a 1002 resistor. Find P (A/B), P (A/C).P (B/C). Resistzoce 10% Total 22 10 14 24 17 28 16 44 100 24 32 Tatal 62 100
What is the Q1 FF steady state answer ? Cik Di Cik Cik
Q4) Draw the IC's diagram of the circuit shown below using the required 74 series DODA B D LL
solve solve solve
When you are as an engineer, when will you decide to use Voltage-Shunt N.F.B? 18- 17- When you are as an engineer, when will you decide to use Voltage-Series N.F.B? 19- When you are as an engineer, when will you decide to use Current-Shunt N.F.B? 20- When you are as an engineer, when will you decide to use Current-Series N.F.B?
01011003 - Electrical/Electronic System Fundamentals - Personal - Microsoft Edge https://college.fordservicetraining.com/SCORM/Shell.html?id=d0c4da2b-dd62-4326-b80f-5b12de237f26&ver=2004 Electrical Fundamentals Which of the following is considered a pushing force? A) Resistance B) Voltage C) Current D) All of the above Back Next 41 of 52 O Type here to search O000
q4 Choose correct answer
Please click on pic to open it
Problem 11: Part (a) At time t = 0 the switch is closed and current flows through the circuit. The current increases with time and eventually reaches a steady state value of imax. Calculate the maximum current imax in units of milliamps. imax = ______ Part (b) Write an equation that relates the current as a function of time i(t) to the maximum current, imax. Express the equation in terms of imax and α, where α = -t/τ. i(t) = ______ Part (c) Determine the time, in seconds, at which the current has a value of i(t50) = 50% of imax. t50 = ______
Control System: Simplify the block diagram
Two coils are placed close to each other as shown in the figure. The coil on the left is connected to a battery and a switch, and the coil on the right is connected to a resistor.What is the direction of the current in the resistori. an instant after closing the switch?ii. after the switch has been closed for several seconds?iii. an instant after opening the switch?Choose your answers betweento. on the leftb. on the rightc. the current is zero.And clearly explain the reason for your answer.