• SUPPORT REACTIONS, • SHEAR AND MOMENT EQUATIONS. FOR THE LAST SEGMENT USE THE FBD OF THE RIGHT SECTION, • SHEAR AND MOMENT ORDINATES, USE RELATIONSHIP BETWEEN THE LOAD, SHEAR & MOMENT DIAGRAM, • DRAW THE SHEAR AND MOMENT DIAGRAMS, • IF ANY, LOCATE THE POSITION OF THE POINT OF ZERO SHEAR, POINT OF INFLECTION AND MAGNITUDE & LOCATION OF THE MAXIMUM MOMENT

Q: Determine the force in member CB of the truss, and state if the member is in tension or compression.…

A:

Q: Q1: Determine the force in each member of the truss in terms of the load P, and indicate whether the…

A: Maximum tension force = 75 KN Maximum compression force = 65 KN a. Determine the force in each…

Q: method of joint member of the

A: degree of static indeterminacy, Ds = m+ r -2j m = total number of members = 13 r =total number of…

Q: To facilitate shifting the position of a lifting hook when it is not under load, the sliding hanger…

A: Given data in question  Mass hanging  Distances  To find out  Magnitude of force in Newton at point…

Q: 3. Three cables are joined at the junction ring C. Determine the tensions in cables AC and BC caused…

A:

Q: 20 mm) 80 mm 20 mm) 120 mm A square box beam is made of two 20×80-mm planks and two 20x120-mm planks…

A:

Q: METHOD OF JONTS 20K 30k B 12 с Tok ICY 5 20 50k E 10' wk 118 G 10 40k 1 Tok I 10' 30k 20k к sok befo…

A:

Q: 150 mm 140 mm 50 mm 60° 130 mm 45 600 N

A: Find the position vector: OA→=130cos30o+50i-130sin30o+140j+150kOA→=162.58i-205j+150k mm The force in…

Q: F2 F1 F1 W W D W G. F - AO E Determine the support reactions at A and E. Determine the forces in…

A:

Q: The beam in the figure has a rectangular cross section of dimensions b and h and is subject to when…

A: Allowable normal voltage (ANV) = 1400 kgf/cm2 = 1.4 x 107 kgf/m2 = 1.4 x 104 tf/m2 Ratio of b/h =…

Q: y В D F A X- P.

A:

Q: Hand

A:

Q: Q3:al Four forces are shown in the figure below at particular locations and orientations with…

A: In the given problem forces are shown on X and Y axis ,  We have to find work done on the origin and…

Q: Using the method of joints, find the reaction forces at the supports and the force in each member of…

A:

Q: ! Required information NOTE: This is a multi-part question. Once an answer is submitted, Consider…

A:

Q: For the simply supported beam subjected to the loading shown, derive equations for the shear force V…

A: Given Beam:- Reaction calculation…

Q: Analyze the girder AB supporting a floor system in Figure 5.20. Stringers, FE and EDC, the small…

A: Given Required : Analyze girder and draw shear force and bending moment diagram for girder

Q: The pin-connected frame shown consists of members ACF, ADG, and BCDE. It is loaded as shown. 200…

A:

Q: Problem Set 5.pd O File C/Users/naswe/Downloads/Problem%20Set%205.pdf ... O | D Page view A Read…

A:

Q: Determine the magnitude (N) of the force in member BC  if  F=335N , a=0.42m, b=2.08m, r=1.09m and…

A:

Q: The device shown is used to straighten bowed decking boards just prior to final nailing to the…

A: Given, r=507 mm s=175 mm α=2.1°β=15° Force=P

Q: T 2' 3' Y Action line of F -5'- D B X

A:

Q: In order to reduce the bending moment in the cantilever beam AB, a cable and counterweight are…

A: Bending moment- A bending moment is the reaction that occurs in a structural element when it is…

Q: If B=650N, determine the: •Direction of the line of action of the resultant force on each member due…

A: Determine magnitude of the resultant force on each member due to pin A

Q: What is the force reaction at support C in units of kips? Assume E is constant. 27 4' 6 8' 3 kips/ft…

A: Answer

Q: Part A Consider the beam shown in (Figure 1). Follow the sign convention. Determine the shear in the…

A:

Q: Find the Ultimate Moment (Mu) of a Wide Flange Section with the following Properties: Web Flange…

A: For ultimate moment capacity, we need to determine the equal area axis, as at the ultimate moment,…

Q: Determine the largest torque T which may be applied to each of the two brass bars shown and the…

A:

Q: O Use the figures on the next page of this handout (or draw your own figures) to draw the free body…

A: P=100lb

Q: Determine the magnitude of force (lb) in member DB of the truss shown if P = 1199 lb, Q=2595 lb,…

A:

Q: Question 1 Find reaction forces and all the force members with the corresponding types of force for…

A: Note: student must check the question again. At B point there is a concentrated load of 820 N in…

Q: 1. (a) Establish the documentation for shear and moment as we did in our class, (b) draw complete…

A:

Q: In the position shown in (Figure 1), cords AB and CAD can each support a maximum tension of 80 lb.…

A:

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6…

A:

Q: AZ B Ф q С

A:

Q: and free b

A:

Q: A с k -8 m B D Not a joint 225 kN 8 m E 75 kN

A:

Q: 2. Discuss and explain with illustration the graphical method in finding the resultant of two or…

A: The resultant is indeed a single force that exerts the same impact as several forces working…

Q: In your response, please display the full computation and all FBDs that were used. Only round off at…

A:

Q: The following problems are given to assess your ability to solve problems on equilibrium of force…

A:

Q: Determine the torsion on the rigid supports and the maximum shearing stress developed in each…

A: Given data,  Total torque = 750 N-m Diameter of AB = 12 mm Diameter of BC and CD = 25 mm   To find…

Q: Answer 9-3,Convert from english to metric units and draw FBD. Write your step by step solutions

A: Given data: Area of each member,A=400mm^2 Modulus of elasticity,E=200GPa

Q: 2.F6 A container of mass m = 120 kg is supported by three cables as shown. Draw the free- body…

A: The given of a conatiner suppoted by three cablle and we have to find out the tension foce iin each…

Q: 2. (a) Replace the force system acting on the post by a resultant force and (b) couple moment at…

A: Given  P= 301 lb

Q: Solve for no.2 Simplify the solutions and write down the formula

A: To find support reaction