Q3:al Four forces are shown in the figure below at particular locations and orientations with respect to a given xy-coordinate system. (1) Find the work due to each force on the origin. (2) Find the torque due to each force about the origin. 2 J 히 13호 : 12 1 M33. 1281 53 30 N -40 y(ma 20 N 60° -2.0 20 N O -2.0 40 2.0 -4.0+ 20 40 N

Q3:al Four forces are shown in the figure below at particular locations and orientations with respect to a given xy-coordinate system. (1) Find the work due to each force on the origin. (2) Find the torque due to each force about the origin. 2 J 히 13호 : 12 1 M33. 1281 53 30 N -40 y(ma 20 N 60° -2.0 20 N O -2.0 40 2.0 -4.0+ 20 40 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PART 2. PROBLEM SOLVIN B 4. ORAW THE SHEAR AND MOMENT DIAGRAM. 3500 1b 500 1b ft 3ft →と eft 3ft
Q.1) Two axial forces P₁ and P2 are applied at point A of a gear system as show below. Determine (a) Magnitude of the resultant force at point A due to these two forces using the Parallelogram method. (b) the x and y components of the resultant force, and the angle between the resultant force and the x-axis. (c) the n and t components of the resultant force. P2 = 300 N 20° y -A P₁ = 100 N 30° X
Kindly answer with complete solution please.
Find the moment with respect to the point A of the force given in the figure
Determine the reactions in pounds the hinge and the rocker exert on the beam supporting the distributed load. (Assume that the +x-axis is to the right and the +y-axis is up along the page. Due to the nature of this problem, do not use rounded intermediate values in your calculations or answers) Magnitude and direction Magnitude in lbs. Ax- Magnitude is 0 Ay- By-
Your answer is partially correct. Replace the three forces shown by an equivalent force-couple system at point A. If the forces are replaced by a single resultant force, determine the distance d below point A to its line of action. 240 N 315 N Answers: M= R= i -345 i -120.60 Force-couple system at A. The force is positive if to the right, and the couple is positive if counterclockwise. Single resultant force. 210 N d = 349.65 670 mm 670 mm 670 mm mm N N.m
Determine the required magnitude of the couple moments M2 & M3 and so that the resultant couple moment of the system shown in Figure Q6 is 052 N.m? M2 45° M3 M = 300 N-m w] TOSHIBA F5 F6 F7 F8 F9 F10 F11 F12 INS SCROLL L &.
PROBLEM 2. For the non- concurrent Force system shoon. Determine the magnitude of the resultant Force and its intersec tion From point Ĥ withn AB. 100ON 700N 1500N 300N 60° 500N-M jm IM 3m
Problem 7.5 For the cantilever beam shown, it is required to determine the point where two bars theoretically can be cut off from the standpoint of the calculated moment strength, OM, of the beam. f, = 420 MPa and f.'= 21 MPa. 420 3@80 = 240 90 mm 90 mm 75 mm 10mmø stirups 4-28mm¢ W. 3.6 m 800 mm 725 mm 12. Calculate the moment the moment strength, ØM, , of the section. [in kN-m] 13. Calculate the maximum factored uniform load, w, the beam could support. [in kN/m] 14. Determine the distance from the free end where two bars theoretically can be cut off. [in m] 15. Determine the distance from the free end where two bars actually can be cut off. [in m] 16. Calculate the required development length, f dr at the support, if 90 hooked bars are used. [in mm]
Determine the values of F and P, if possible so that the force system shown in cases (b) through (d) are equivalent to the force system shown in case (a). F and P must maintain their direction as drawn. This is a problem where explanations will be critical to explain the logic you used. 12 kip |F 8 ft 4 kip 4 ft 4 ft 4 ft 4ft 4 ft 4 ft (a) (b) 2 kip 2 kip 2 kip (c) (d)