Subject name is Linear Control system. I need step by step block diagram reduction rule and also required signal flow graph

Q: 3. What is harmonic restrain and startup characteristic for differential protection and in which…

A: This protection system is employed to protect alternator, transformer and high rating HT motor.…

Q: (i) Describe the function of a voltage to frequency converter. (ii) Given Vi = f /50. Calculate the…

A: (b) The given figure is shown below:

Q: Draw the electronic circuit of ON/OFF controller and also write the electronic output equation and…

A: The electronic circuit of ON/OFF controller is given as:

Q: 1- Explain briefly another way for implementing a Momo stable Multivabrator Circuit other than by…

A: "Since you have posted multiple questions, we will provide the solution only to the first question…

Q: 4.A 200 V, 20 A, 200 rpm, separately excited DC motor is having an armature resistance of 2 2. It is…

A: Given,V=200VIa=20AN=2000 rpmRa=2ΩVs=230VN1=900 RPMα=85°

Q: What type of feedback controller is shown in figure A. PD controller B. PI controller C. Type 2 D.…

A:

Q: c)What is the role of error detector and feedback in a closed-loop control system?

A: modified control system

Q: A 240 V, 50Hz single phase supply feeds a SP-FC-FWR. The rectifier is used to power the armature of…

A:

Q: In the experiment of dc motor drive using three phase half wave rectifier, when the torque load…

A: DC motor drive by 3 phase half wave rectifier.  What is effect of current in the torque.?  If torque…

Q: Discuss merits and demerits of feedback in  control system .  Give 5 points for each brief only

A:

Q: The system given in following figure, is an example for Gear Assembly for reducing shaft speed…

A: Given that  What is type of system shown figure

Q: Explain the use of controllers in Control system. What is proportional controller and with example?

A: Controllers are fundamental part of control systems.  A controller is a device which commands and…

Q: i) Draw the electronic circuit of P controller and also write the electronic output equation and…

A: High ON switch voltage is VH=Vsp Low OFF switch voltage is VL=VSP-R1R2Vo The main advanstages:…

Q: d) A200V, 875rpm, 150 Amp separately exited D.C. motor has an armature resistance of 0.0652. It is…

A:

Q: A single-phase full-wave controlled rectifier is connected to a 200 Vms AC voltage source to feed…

A: Consider the given data. The rms voltage is 200 V The field resistance is 0.06 ohm The armature…

Q: 2.⁠ ⁠What is the scan chain? How is it used to help observability and controllability to achieve…

A: The objective of the question is to understand the concept of a scan chain and its role in enhancing…

Q: At -- angle, the three phase full converter drive gives an armature voltage of 220V, while the AC…

A: Choose the correct option What is firing angle of the converter.  If the terminal voltage = 220V and…

Q: 3. What are the limitations of Multivibrator? Briefly discuss how multivibrator can be used as a…

A:

Q: The machine in Q4a has what kind of compounding characteristic? O Differential Shunt Under Over Flat

A: .                               SOLUTION                      .…

Q: For a single phase (ac to ac) voltage controller, if the input supply voltage is (250Sin314t) with…

A: Peak Value of the supply voltage (Vm) = 250 V           Load resistance (R) = 5 Ω

Q: Q4/ Define the armature reaction, at no load what is the armature reaction value and how to reduce…

A: The explanation is as follows.

Q: Discuss the importance of form factors in motherboard selection and installation.

A: Form factors in motherboards dictate their physical dimensions, layout, and specifications. Crucial…

Q: Which of the following part of DC machine is known as mechanical rectifier? Rotor Commutator Stator…

A:

Q: It is a control system in which the control action is independent of the output. A.)closed loop…

A: The solution is given below

Q: Explain how poles and zeros are important in a feedback control system and t differences between…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: A position control system converts a position input command to a position output response. For…

A:

Q: A de machine is controlled by the step-down de-de converter shown below. The armature inductance La…

A: The question is about buck converter circuit.

Q: s3 + 5s2 + 12s +K = 0. Find the range of K for all the roots to lie to the The characteristics…

A: Find the range of K for all the roots to lie to the left of s =1 for the given characteristic…

Q: A 240 V, 50Hz single phase supply feeds a SP-FC-FWR. The rectifier is used to power the armature of…

A:

Q: Discuss the concept of linearization and why it is essential in control system design

A: Linearization is the process of approximating a nonlinear system with a linear system around…

Q: The feedback elements of control system alternatively called as O a. Process element O b.…

A: Feed back element is sensing element or instrumentation element .

Q: what are the Motor control techniques can be used and the Suitable Microcontroller for above design…

A: Closed Loop Motor control techniques is very important in industrial applications such as running a…

Q: 5) Explain the working diagram. characteristics equation for feedback control Es? + 12s + K = 0.…

A: Note : We are authorized to answer one question at a time, since you have not mentioned which…

Q: A PI current control is developed for a de machine based on pole zero cancelation. The following…

A: DC Machine: A DC machine is an energy-altering electromechanical device. When electric current…

Q: From the phasor diagram in the figure, deduce a expression for the output power, as a function of…

A: Given characteristics is of  synchronous machine in motoring mode Ef lags Vt  by angle δ

Q: Explain the fundamental differences between open-loop and closed-loop control systems. Provide…

A: Open-Loop Control System:An open-loop control system is a type of control system where the control…

Q: What is difference between Open-loop and Close-loop control system? give note on both

A: Open loop control system : The open loop control system is the control system in which there is no…

Q: In closed loop control system, the output of comparator element is O a. Feedback signal O b. Error…

A:

Q: A 240 V, 50Hz single phase supply feeds a SP-FC-FWR. The rectifier is used to power the armature of…

A:

Maximum power transfer theorem

A resistive load will consume maximum power from a network when the load resistance is equal to the resistance of the network as viewed from the open-circuit terminals, with all energy sources removed leaving only the internal resistances. Physicist Moritz von Jacobi introduced the maximum power transfer theorem in 1940. Therefore, this theorem is also known as Jacobi's law.