Steel shaft AD (G = 80 GPa) is subjected to torsional loads at sections B and D, as shown in the figure. The diameters are: d1 = d2 = 40 mm., and d3 = 30 mm. (a) Determine the amount of torque T D φ C added at D that would make the rotation at C equal to zero, that is, let = 0. (b) For the loading as determined in Part (a), determine the maximum stress of shear in each of the three shaft segments. (answers: ?AB=-17.4 MPa ,?BC = 90 MPa ?CD=52 MPa, TC= -119 N.m, TD= 278 N.m)

Q: Q.I: A shaft composed of segments AB, BC is fixed between the two walls at A and C and loaded as…

A:

Q: Axial loads are applied to the solid cylindrical rods as shown. The loads P = 1500 lb, Q = 900, and…

A: Compound rods are constructed from sections of different materials, lengths and areas. They may be…

Q: 20 kip By 1 ft E 1.5 ft 3 ft

A: given data: elasticity(E)=10*103ksi=68.95*103MPa force applied at B point =20kip=88.964KN…

Q: 6 - A circular bar is subjected to a lateral load and axial torque, as shown in the figure. If the…

A: Givenτ=100  MPa

Q: A solid circular bar ABCD with fixed supportsat ends A and D is acted upon by two equal…

A: Given   Torque = T0  Length  = L  Find   Distance, x   Angle of twist

Q: A circular tube of inner radius r1 and outer radius r2 is subjected to a torque produced by forces P…

A: a-calculate the r2 the minimum permissible outer radius of the tube given…

Q: A torsional moment T = 6,467 Nm and a load P = 87,599 N are applied at the same time to a circular…

A: This question is related to the torsion of the shaft. torsional shear stress or Torsional stress is…

Q: The triangular block shown in the figure is subjected to the loads P = 1600 lb. and F = 600 lb. If…

A:

Q: The set shown in the figure consists of an aluminum ABC tube, with section AB having a diameter of…

A: Givendiameter of tube AB d1=20mmdaimeter of section BC d2=60mmP=4000N

Q: A steel rod (E = 200 GPa) is fixed at A and subjected to the loading shown in the figure. The…

A: To find: The displacement of rod at D. Given: The young's modulus of steel rod is E=200 GPa. The…

Q: A composite shaft consists of a brass sleeve securely bonded to half steel shaft, fixed at  end A as…

A: Given data:

Q: A prismatic bar AB with a solid circularcross section (diameter d) is loaded by a distributedtorque…

A:

Q: 3.8-4 A hollow steel shaft ACB of outside diameter 50 mm and inside diameter 40 mm is held against…

A:

Q: Q4: A 5 m long hollow bar of circular section has 160 mm diameter for a length of 3m, while it has…

A: To find: The elongation of the long hollow bar.   Given: The total length of the bar is L=5 m The…

Q: A steel bar of cross section 500 mm2 is acted 45 kN upon by the forces shown in Figure. Determine…

A:

Q: For the given system below, rods A and B support the rigid bar, pinned at O, as it is subjected to…

A:

Q: 6 - A circular bar is subjected to a lateral load and axial torque, as shown in the figure. If the…

A: Given data: Length of the bar (L) = 600 mm = 0.6 m Diameter of the bar (D) = 50 mm = 0.05 m Distance…

Q: ircular tube of aluminum is subjected to torsion by torques T applied at the ends (see figure). The…

A: Given:L=27 indi=1.2 indo=1.6 inθ=3.157°T=51,662 in

Q: A hollow steel shaft ACB of outside diameter 50 mm and inside diameter 40 mm is held against…

A: Outside diameter = 50 mm Inside diameter = 40 mm Shear stress = 55 Mpa

Q: The structure in the figure is composed of two rigid bars (AB and CD) and two vertical rods made of…

A: The given information in the problem is listed in the following attached image:

Q: . The rigid bar AB attached to aluminum and steel rods, is horizontal before the load P is applied.…

A:

Q: y T H A (1) B

A: You asking only Area and Polar moment of inertia so i provide only that,i hope you understand.

Q: Two horizontal bars ABC and DEF are rigid and originally horizontal and the links CE and DG are 1/4…

A:

Q: A hollow circular stainless steel bar is loaded in tension by force P. The bar has a length…

A: Given data is

Q: Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1)…

A:

Q: Q 2 : The homogeneous wire ADOBC is bent into a semicircular arc and two straight section as shown.…

A:

Q: A steel column member shown in the figure below is pin- connected at the two ends. It could fail…

A:

Q: Four wooden dowels with a diameter of 30mm are attached to a board. Two ropes pass around the…

A: Given data  Diameter = 30mm Force P= 110N and Q= 189N Find the resulting torque

Q: The uniform solid cylindrical bar AB (torsional rigidity = GIp), shown in the figure, is fixed at…

A:

Q: Vertical load is applied to point B of a 10 mm radius cylindrical bar as shown in the figure.…

A:

Q: Practice Problems P2. A uniformly tapering rectangular rod is subjected to load as shown in the…

A: A uniformly tapered rod is one in which the cross-section varies uniformly throughout its length. If…

Q: A rigid bar, pinned at O, is supported by two identical springs as shown in the figure. Each spring…

A: The maximum allowed load can be determined from the shear stress condition as shown below.

Q: F2. A circular shaft fabricated from steel is supported at each end by rigid constraints, as shown…

A: Given data: LA=LB=60 in=5 ftT=900 ft.lbdA=2.5 in=0.208 ftdB=2 in=0.1667 ft Need to determine the…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.