steel rod 250 mm long and 200 mm in diameter is being reduced to 190 mm in diameter all over its length in one travel. The machine spindle rotates at 500 rpm, whereas the tool is moving at an axial feed of 0.5 mm/rev; calculate the following: Material removal rate (mm3/min) Consumed gross power in Nm/s if cutting force is 477.5N and mechanical efficiency is 90% Cutting time

Q: 3. A 50-mm-long, 30-mm-diameter hole in a steel rod is being enlarged in diameter to 31 mm by one…

A:

Q: Calculate the r/min required for finish turning

A:

Q: From the speed chart below, determine the correct cutting speed for performing a facing cut on Brass…

A: Milling is the process of machining the surface of the object. Milling is done with the help of a…

Q: Q3). A block of 190mm length and 100mm width is to be machined in shaping process. The permissible…

A:

Q: The orthogonal cutting of steel is done with 10° rake tool with a depth of cut of 4mm feed rate of…

A: Merchant circle:

Q: An external turning operation is performed on a hollow workpiece of 200 mm external diameter and 100…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: The shear angle

A: Given; Rake angle of orthogonal cutting of MS is;   α=100Chip thikness ratio=0.4Determine shear…

Q: A 16mm Solid carbide tool with two teeth is used to machine Aluminium using the cutting speed of…

A:

Q: A 78 mm thick plate is to be milled down to a thickness of 60 mm using an 80 mm face milling cutter.…

A: The processing time required is 30.61625 min.

Q: It is required to reduce the thickness of cast iron workpiece with dimensions (L x w x t) of (230 mm…

A:

Q: List down three types of milling cutters used in machining process and sketch their cutting process.…

A: d) face milling, double angle milling & form milling cutter e) v=rw

Q: Calculate the machining time to complete the job as shown below from a bar 120 mm long and 60 mm…

A: Given: length of the job→L=120 mm initial diameter→D=60 mm  maximum depth of cut→d=5 mm hence in…

Q: . Draw the forces and angles involved in the cutting process and calculate shear angle (Ø), friction…

A:

Q: Draw the forces and angles involved in the cutting process and calculate shear angle (Ø), friction…

A:

Q: Determine time required for machining?

A: Given data;  A 600mm×30mm flat surface of a plate is to be finsih machined on a shaper. Plate is…

Q: 39- An orthogonal cutting operation is being carried out under the following conditions: t0-D0,38…

A: Givent0=0.38mmtc=0.65mmwidth of cut=2.5mmV=3.5m/srake angle=6°Fc=515NFt=210Nto find:-Percentage of…

Q: Since the cutting plane angle is 9.5°, the cutting depth is 0.4 mm, the chip thickness is 2.9 mm,…

A: 1.We know that rack angle=Cutting plane angle=9.50

Q: In a cutting test with 0.3 mm flank wear as tool failure criterion, a tool life of 10 min was…

A: Taylor's tool life equation is given by F.W. Taylor. Taylor's tool life equation gives the relation…

Q: 1. Using the Taylor equation for tool wear and let: n = 0.3, calculate the percentage increase in…

A: Tool life exponent, (n)=0.3 The cutting speed is reduced by 30% and then increase by 20%. Determine…

Q: Find the machining time required to turn a mild steel rod from 65mm to 58 mm over a length of 100 mm…

A: Given data: The diameter of the shaft before machining is D = 65 mm. The change in diameter of the…

Q: In machining a mild steel work piece with carbide tool, the life of the tool was found to be 1 hour…

A:

Q: A cylindrical workpart 200 mm in diameter and 700 mm long is to be turned in an engine lathe.…

A: Given Data- D=200mm L=700mm f=0.32 mm/rev d=1.80mm Vc=2.30 m/s We have to find Cutting time and MRR

Q: Aluminum bar with 100mm diameter and 500mm long is turnmed down to 88mm diameter, using two passes…

A:

Q: 17) A50-mm-dia endmill cuts 6061 aluminum with 30% tool engagement at a depth of 6 mm. The tool…

A:

Q: A student is using a lathe with 80-hp and 80% efficiency to fabricate a copper alloy with Sy= 1200…

A: To Find : The maximum depth of cut. Given : The power is P=80 hp0.7457 kW1 hp=59.656 kW. The yield…

Q: A single point cutting tool with 0°rake angle is used in an orthogonal machining process. At a…

A:

Q: The following data is given for slab milling of a 300 mm long 50 mm wide mild steel block: Cutter of…

A:

Q: 3. It is required to machine a slot with length 100 mm, width 15 mm, and depth 4 mm. Calculate the…

A: Given: The length of machine slot, L = 100 mm The width of machine slot, b = 15 mm The depth of…

Q: A flat milling operation will be carried out with a horizontal milling machine, in a piece of 250 mm…

A: Milling operation is the manufacturing technique that is done on a milling machine. In this…

Q: A tool with zero rake angle used in orthogonal cutting when its clearance angle a is changed from 10…

A: Given:initial rake angle, α1=10ofinal rake angle, α2=7o

Q: Calculate the time required for completing

A: Given DataDepth of cut d = 5 mmwith  w = 150  mmLength of the elate l= 600 mmThickness t = 25…

Q: A turning operation is carried out on aluminum. Based on the specific energy values in the table in…

A:

Q: A 16mm Solid carbide tool with two teeth is used to machine Aluminium using the cutting speed of…

A:

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.