steel cylindrical air receiver with 5 ft. diameter and pressure load of 180 psi, design stress of 9500 psimaximum. The pressure vessel is to be provided with 1 ½ in. diameter drain valve installed at the bottomof the vessel and safety pressure relief valve installed either at the topmost or at the side with pop-outrating of 200 psi. Assume a 100% weld joint efficiency. The lap welding tensile strength is 65,000 psi.Determine the bursting pressure of this air

steel cylindrical air receiver with 5 ft. diameter and pressure load of 180 psi, design stress of 9500 psimaximum. The pressure vessel is to be provided with 1 ½ in. diameter drain valve installed at the bottomof the vessel and safety pressure relief valve installed either at the topmost or at the side with pop-outrating of 200 psi. Assume a 100% weld joint efficiency. The lap welding tensile strength is 65,000 psi.Determine the bursting pressure of this air

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter15: Gas Metal Arc And Flux Cored Arc Welding Aws Sense Certification

Section: Chapter Questions

Problem 10R: According to Practice 15-6, after each weld pass the test plate should be allowed to cool but never...

See similar textbooks

Similar questions

5. A steel cylindrical air receiver with 5 feet diameter and pressure load of 180 psi, design stress of 9500 psi maximum. The pressure vessel is to be provided with a 1.5 in diameter drain valve installed at the bottom of the vessel and a safety pressure relief valve is installed either at the topmost or at the side with a pop-out rating of 200 psi. Assume a 100% weld joint efficiency. The lap welding tensile strength is 65,000 psi. Determine the bursting pressure of this air receiver. psi
Show your complete solution.
An axially-loaded welded angular connection is shown SD-002 . The angular section 150 x 100 x 10 mm having an area of 2400 mm? is welded to a gusset plate having a thickness of 10 mm. All steel is A 36 (Fy = 248 MPa, Fu = 400 MPa) and E (70) electrodes (Fu = 484 MPa) is used. Using the shielded metal-arc welding process. Compute the value of "a" if T = 500 kN. (Please do not round-off to whole number the required thickness, use the exact (2 decimal) value.) 150 mm SD-002
strength of materials
A continuous fillet wild is used to weld two pieces of 7.0-mm-thick austenitic stainless steel plate in an arc-welding operation. The plates are joined at a 90° angle using an inside fillet corner joint. The velocity of the welding head is 6 mm/sec. Assume the cross section of the weld bead approximates a right angle isosceles triangle (a right triangle with the two legs and their corresponding angles equal) with a leg length of 4.5 mm. The length of the weld = 230 mm. The melting factor of the setup = 0.65, the heat transfer factor = 0.90, and the Tm for austenitic stainless steel = 1670°K. Determine (a) The amount of heat (in joules) required to melt the volume of metal in (b) The heat that , (c) The rate of heat generation required at the welding source to accomplish the weld this weld (filler metal plus base metal) must be generated at the heat source
On all CJP groove welds in butt joints transverse to the computed tensile stress, they:
Describe an ideal tack weld.
Does all of the heat produced by an SMA weld stay in the weld? Why or why not?
Material Strengths: Fy = 248 MPa, Fu = 400 MPa Method: Use ASD. A single angle L127X89X19 is welded (longitudinal and transverse welds) on one leg (shorter leg) togusset plate; thus, there are no holes. The length of the longitudinal welds is 150 mm. Which of the following most nearly gives the allowable tensile load?
Determine the length of the weld run for a plate of size 120 mm wide and 15 mm thick to be welded to another plate by means of 1. A single transverse weld; and 2. Double parallel fillet welds when the joint is subjected to variable loads. (hint: From Table 10.6, we find that the stress concentration factor for transverse weld is 1.5 and for parallel fillet welds is 2.7). A B
Calculate the heat input during the arc welding process, if the voltage is 32 volts, current is 120 amperes, the length of the weld is 94mm and the time to complete the weld 33 secs. 1-Speed S= 2-Heat Input (Watts)=
Instruction: : Explain the wOrking principle Of bOurdOn tube type pressure guage