119 ABOUT INDUSTRIAL PIPING HOW SHOULD LOAD AND ENERGY BALANCE BE DONE IN A BRANCHED PIPING SYSTEM?

Q: 33. An open drive condensing unit has the following factory delivered options. • Compressor maximum…

A: Given, For compressor Size of compressor,D1=600mm maximum speed of compressor, N1=550rpm For motor,…

Q: A pump is to be placed at the beginning of a 30 m long piping system consisting of 1-1/2 inch…

A: Release head differs with pull tank level. The response is yes. Assuming you bring down the pull…

Q: State two reasons copper pipe is becoming more popular for fire protection systems

A: Almost all fire protection systems use carbon steel, but the use of copper in fire protection…

Q: What is the length of the finned section of pipe in this baseboard hot waterheating system?

A: Find    Calculate the length of the finned section of the pipe

Q: I have three parts that need to be answered pertaining to the print provided below.   What size…

A: The size of the print provided in the title box is C.Hence the correct answer is C.

Q: why bare pipe has 0% efficiency and full covered insulate pipe has more efficiency

A: A thermal insulator has a low thermal conductivity and is a poor heat conductor. To reduce heat loss…

Q: 111 about industrial piping WHAT IS THE RELATIONSHIP BETWEEN OPERATING PRESSURES, MAWP, HYDROSTATIC…

A: The question is asking about the relationship between different pressure parameters in the context…

Q: Mention any 5 advantages of thermocouple?

A: Thermocouples work on the principle of the Seebeck effect. The Seebeck effect: if two different…

Q: Q1: Explain what do we mean by rectifier? How it works, what type of welding machines have a…

A:

Q: The general specification for production tubing is

A: After the casing has been run and cemented in place, production tubing is run into the drilled…

Q: 113 About industrial piping UNDER WHAT CONDITIONS SHOULD FLOW VELOCITIES BE LIMITED?

A: The objective of the question is to understand the conditions under which flow velocities in…

Q: List some applications that use low-pressure piping

A: The low-pressure piping systems are used to carry nonhazardous materials that are used in Industry.…

Q: 180 about industrial piping WHAT CHANGES FROM THE CANTILEVERED BEAM METHOD TO THE CASTIGLIANO…

A: The objective of the question is to understand the differences between the Cantilevered Beam method…

Q: An uninsulated steam pipe passes through a room in which the air and walls are at 25°C. The outside…

A:

Q: According to ASME B.31, what is the value of Y (reduction coefficient) in the formula below (wall…

A: The objective of the question is to find the value of the reduction coefficient (Y) for austenitic…

Q: Is the Hotelling Rule applicable to oil?

A: Hotelling's hypothesis, often known as Hotelling's rule, states that nonrenewable resource…

Q: What is the simplest industrial piping system (simplest to design and develop)?

A: The objective of the question is to identify the simplest industrial piping system in terms of…

Q: Industrial Pipes Are pipes with screw connections not used when they have a large…

A: The question is asking whether the cost of threading is the primary reason why screw connections are…

Q: 017 ABOUT INDUSTRIAL PIPING WHEN TO USE SPRING SUPPORTS WORKING UNDER COMPRESSION OR UNDER TRACTION?

A: The objective of the question is to understand when to use spring supports working under compression…

Q: Give all the parts of a simple vertical fire tube boiler

A:

Q: Illustrate the different components of Evacuated Tube System

A: The evacuated tube system is used to collect the blood samples.

Q: What is the minimum gas flow rate for a nozzle size?

A: Given: What is the minimum gas flow rate for a nozzle size?

Q: hy there is a little amount of heat loss for fully covered insulated pipe compared to bare pipe?

A: To state the reason why there is a little amount of heat loss for fully covered insulated pipe…

Q: 118 ABOUT INDUSTRIAL PIPING IN WHAT SITUATION IS IT NECESSARY TO PERFORM FLEXIBILITY CALCULATION IN…

A: The objective of the question is to understand the situations where it is necessary to perform…

Q: 114 About industrial piping: HOW ARE EXPANSION JOINT CALCULATIONS MADE?

A: The objective of this question is to understand how to calculate the requirements for an expansion…

Q: industrial application of fire tube and water tube boiler

A: Fire tube boilers: It is the type of boilers in which hot gases are passed through the tubes which…

Q: <Chapter 10 section 4 Item 4 Sve stav The assembly consists of two pipes and a plate. (Eigure 1)…

A:

Q: Given the hook-up drawing, list all the equipment, tools and materials that are needed in…

A:

Q: 020 ABOUT INDUSTRIAL PIPING WHAT ARE THE POSSIBLE TRANSIENT OPERATING CONDITIONS FOR PIPING SYSTEMS?

A: The objective of the question is to identify and explain the possible transient operating conditions…

Q: 8. A prismatic bar AB of length 6m and weight 3 KN is hinged to a wall and supported by a cable BC.…

A: Given Data:*AB=6m*weight w=3 KNTo finda)Hinge reaction Ax=? Ay=?b)tension oin BC, T=?