Steam is supplied, dry saturated at 40 bar to a turbine and the condenser pressure is 0.04 bar. The plant operates on the Rankine cycle and the expansion process has an isentropic efficiency of 80 %. a) Sketch the Rankine cycle on a T-s diagram. b) Calculate i) the cycle efficiency, and ii) the specific steam consumption.

Steam is supplied, dry saturated at 40 bar to a turbine and the condenser pressure is 0.04 bar. The plant operates on the Rankine cycle and the expansion process has an isentropic efficiency of 80 %. a) Sketch the Rankine cycle on a T-s diagram. b) Calculate i) the cycle efficiency, and ii) the specific steam consumption.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An ideal Rankine cycle operates between the pressure limits of 15 MPa in the boiler and 50 kPa in the condenser. The boiler generates steam at a mass flow rate of 50 kg/ s and it enters the turbine at a temperature of 1100°C. a) Calculate the net power output of the cycle, b) Calculate the thermal efficiency of the cycle.
An Ideal rankine cycle steam (7 MPa, 10kPa).Ideal Rankine vapor power cycle operates with steam.Saturated vapor enters the turbine at 7 MPa.The condenser pressure is 10 kPa. Determine thea. turbine work, in kJ/kgb. Condenser heat transfer, in kJ/kgc. Pump work, in kJ/kgd. boiler heat transfer, in kJ/kge. thermal efficiencyf. back work ratio
1. A reheat steam cycle has 13,580 kPa of throttle pressure at the turbine inlet and a 37.50308414 atm reheat pressure, the throttle and reheat temperature of the steam is 1302 R, condenser pressure is 4.3 kPa. Determine the difference between the simple Rankine cycle efficiency and the reheat Rankine cycle efficiency, in percent.
A piston engine operating on the Carnot cycle uses air as the working fluid. At the start of isothermal expansion air is 521 psi & 1100°F. Isothermal Expansion ratio = 1.25. Isentropic Compression ratio = 3.2. The amount of air circulated is 15 Ibm/min. Draw and label the P-V and T-S diagram. Determine the following; a.) Temperature of the sink, °F b.) The Carnot cycle efficiency, in % c.) Power output, Hp d.) Mean effective pressure, psi
In an ideal regenerative cycle, the steam expands in the turbine from 1100 psia and 1100 F to 80 psia, where m lb of steam is extracted for feedwater heating (open heater). The remainder continues expansion to a condenser pressure of 1 psia, 200 F. The throttle flow is 100lb/sec. The brake engine efficiency is 80% and generator efficiency is 84% Compute: a. Ideal combined heat rate, Btu/kW-hr
Draw the schematic or plant layout. Draw the T-s diagram Mandatory: A, B, C Suggested: D, E A reheat cycle has the following data: Throttle, 8.5 MPa at 400°C Turbine exhaust, 0.06 MPa For an ideal cycle, determine the: (A) Work (B) Thermal efficiency (C) Heat rate (D) What is the thermal efficiency of the corresponding Rankine cycle? (E) What is the percent improvement in engine heat rate of the reheat cycle from the Rankine cycle.
An Ideal Rankine cycle operates on a boiler and condenser pressure of 2MPa and 20kPa respectively. Steam leaves the boiler at 500C. The cycle produces a Net Power of 10MW. Determine the a.) Thermal efficiency of the cycle(%), b.) steam rate of the turbine. (kg/kW-hr), and c.)heat rate of the cycle (kJ/kW-hr) PLS SHOW COMPLET SOLUTIONS
An Actual Rankine cycle operates on a boiler and condenser pressure of 2MPa and 20kPa respectively. Steam leaves the boiler at 500C. Steam flows at a rate of 10kg/s in the cycle. The Turbine and Pump Efficiency are provided to be 87% and 89% respectively. a.) Determine the Heat Added to the boiler (kJ/s) b.) Determine the Work done by the pump (kJ/kg) c.) Determine the Thermal Efficiency of the Cycle (%) ROUND OFF ANSWER TO SIX SIGNIFICANT FIGURES PLS USE THE GIVEN VALUES THAT IS HIGHLIGHTED IN THE IMAGE OF THE STEAM TABLE AND SUPERHEATED TABLE PLSS USE THIS VALUES
5) Analyse a cogeneration Rankine cycle with the following conditions: Heat input to the cycle: 20 MW • Inlet conditions to the turbine: 3.0 MPa, 350 °C • Intermediate steam conditions (for the process): 1.0 MPa, 50 % of the mass flow • Condenser saturation temperature: 40 °C Isentropic efficiency of the pumps and turbine: 75 % Clearly state any assumptions.
subject: thermodynamics A turbine is supplied with steam at 25 BAR, 42C and exhaust into a condenser at 55 KPa. Find the thermal efficiency of the cycle. Draw the schematic and T-S diagrams with corresponding labels.
Task 4: Why we need for superheated steam in the bottoming cycle (Rankine cycle). Task 5: - Calculate the moisture content at the exit of the turbine in the bottoming cycle (Rankine cycle). - Apply the use of tables to establish steam plant efficiency. Task 6: Justify why the Rankine cycle is preferred over the Carnot cycle in steam production plants around the world.