Steam at 50 bar and having an enthalpy of 3100 kJ/kg is supplied to a turbine and comes out at 0.10 bar and enthalpy of 2100 kJ/kg. A feed heating is done by extracting the steam at 3.2 bar with an enthalpy of 2500 kJ/kg. The condensate from condenser with an enthalpy of 125 kJ/kg is fed into the feed heater of direct mixing type. The quantity of bled steam is 11200 kg/hr. Find the power developed by the turbine Neglect nump work

Steam at 50 bar and having an enthalpy of 3100 kJ/kg is supplied to a turbine and comes out at 0.10 bar and enthalpy of 2100 kJ/kg. A feed heating is done by extracting the steam at 3.2 bar with an enthalpy of 2500 kJ/kg. The condensate from condenser with an enthalpy of 125 kJ/kg is fed into the feed heater of direct mixing type. The quantity of bled steam is 11200 kg/hr. Find the power developed by the turbine Neglect nump work

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The LiBr-water absorption cycle shown in the Fig. operates at the following temperatures: generator, 105 C; condenser, 35 C; evaporator, 5 C; and absorber, 30°C. The flow rate of solution delivered by the pump is 0.4 kg/s. (a) What are the mass flow rates of solution returning from the generator to the absorber and of the refrigerant? (b) What are the rates of heat transfer at each of the components, and the COP? High-pressure vapor Solution 105 Generator Heat Pump Monog Heat Condenser Throttling Expansion valve valve Low-pressure vapor Heat Absorber Evaporator Heat
considet m kg out of 1gk id taken to the feed henter
Saturated vapor R22 refrigerant leaves the evaporator and enters the compressor at 131.68kPa. The refrigerant leaves the condenser as a saturated liquid at 40oC and enters theexpansion valve at 36oC. Heat rejected from the condenser amount to 105 kW. The work tothe compressor is 65 kJ/kg, while the heat loss from the compressor is 5.5 kJ/kg. A 7.4 kJkgof heat loss in piping between the compressor and condenser, Draw the p-h diagram(labeling the pressures and temperatures in each condition). Determine (a) the temperatureof refrigerant entering the condenser and (b) calculate the refrigeration capacity in tons.
3. An ammonia simple saturation cycle operates between evaporator and condenser temperatures of -20°C and 35°C, respectively. The system is to be used in producing 5000 kg of ice at – 12°C from water at 29°C in 20 hours. Assuming losses to be 20 per cent of the heat to be absorbed from the water. Determine (a) the mass flow rate of the refrigerant, (b) the heat rejected at the condenser, and (c) the power required by the compressor.
9. A vapour compression plant is powered by a 2kW motor and circulates R12 at 5kg/min. The R12 leaves the condenser at its saturation temperature with a specific enthalpy of 74.59kJ/kg and leaves the evaporated dry saturated with a specific enthalpy of 187.53kJ/kg. Calculate: (a). the dryness fraction at the evaporator inlet (b). refrigeration effect (c). coefficient of performance
اريد حل كتابة يد
ercise 6 6.1 A surface condenser is fitted with separate air and condensate outlets. A portion of the cooling surface is screened from the incoming steam and the air is passes over these screened tubes to the air extraction and becomes cooled below the condensate temperature. The condenser receives 20 000kg/hr of dry saturated steam at 36.2°C. At the condensate outlet the temperature is 34.6°C TK and at the air extraction the temperature is 29°C. The volume of air and vapour leaving the condenser is 3.8m3/min. Assume constant pressure throughout the condenser, calculate: 6.1.1 the mass of air removed per 10 000kg of steam (2.63kg); 6.1.2 the mass of steam condensed in the air cooler per minute (0.5kg/min)%3B 6.1.3 the heat rejected to the cooling water (13451kW).
Superheated steam from the boiler expands in the turbine from inlet pressure p₁ of 50 bar and temperature 7 of 487 °C to condenser pressure p2 of 18 kPa. In the condenser, the steam condenses to saturated water. The isentropic efficiency of the turbine ns is 78.0 %. The mass flow of steam 9m,h is 140 kg/s. In the boiler, heat flow rate to the circulating fluid (water/steam) is 458 MW. Read from h,s-diagram and calculate: 1. Enthalpy of the superheated steam h kJ/kg (with zero decimal accuracy) 2. Enthalpy of the steam at turbine outlet after isentropic expansion h₂s kJ/kg (with zero decimal accuracy) 3. Enthalpy of the steam at turbine outlet h₂ kJ/kg (with zero decimal accuracy) 4. Turbine power Pt MW (with one decimal accuracy) 5. Steam content at the turbine outlet X2 kJ/kg (with two decimal accuracy) 6. Enthalpy after condenser h3 kJ/kg (with zero decimal accuracy) 7. Thermal power of condenser Qc 8. Thermal efficiency of the plant n MW (with one decimal accuracy) % (with one…
Steam enters the turbine at 10 MN/m? and 450°C. The steam expanded isentropically in the turbine down to the condenser pressure of 20 kN/m?. The power developed by the plant is 5600 kW. The condensate leaving the condenser is pumped to the boiler pressure isentropically. Taking into account the pump work and calculate: The mass of steam generated in the boiler. • Cycle thermal efficiency. • Specific steam consumption. Draw the cycle on a T-s diagram. Hint: 1 MN/m = 10 bar %3D
11. A vapour compression refrigeration plant uses ammonia. The compressor takes vapour from the evaporator at 207.7kPa and -8°C and delivers to the condenser at 1470kPa and 113°C. The temperature of the liquid leaving the condenser at a rate of 12kg/min is 38°C. Calculate: (a). the dryness of the refrigerant entering the evaporator (b). the cooling load (c). the power to the compressor (d). coefficient of performance (e). plant capacity
The evaporator (a heat exchanger) in an A/C unit has R-410A entering at -20 °C and a quality of 30% and leaves at the same temperature and a quality of 100%. The COP of the air conditioner is known to be 1.3 and the mass flow rate is given as 0.013 kg/s. Find the power input to the cycle. (Note that, here, the evaporator is the part of the A/C unit that accepts [i.e., withdraws] heat from the room maintained at a cold temperature)