Steam at 2 MPa and 250°C in a rigid cylinder is cooled until the quality is 30%. Find the heat rejected from the cylinder. @ 2 Mpa and 250°C: υ = 0.11144 m3 /kg u = 2679.6 kJ/kg @ 2 Mpa, (saturated):υf = 0.0011767 m3 /kg υg = 0.09963 m3 /kg uf = 906.44kJ/kg ug = 1693.8 kJ/kg

Steam at 2 MPa and 250°C in a rigid cylinder is cooled until the quality is 30%. Find the heat rejected from the cylinder. @ 2 Mpa and 250°C: υ = 0.11144 m3 /kg u = 2679.6 kJ/kg @ 2 Mpa, (saturated):υf = 0.0011767 m3 /kg υg = 0.09963 m3 /kg uf = 906.44kJ/kg ug = 1693.8 kJ/kg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Shown in the figure, an insulated rigid tank is divided into two equal parts by a partition. Initially, one part contains an indeal gas, and the other part is evacuated. The partition is then removed, and the gas expands into the entire tank. At the initial state, the mass of the gas is m= 4.00kg, initial pressure is p1 = 600.00 kPa, initial temperature is T1 = 300.00 K. The gas constant is R = 0.2870 kJ/(kg·K). (The internal energy can be determined by the equation ΔU=m·cv·(T2-T1), where cv = 0.7180 kJ/(kg·K) is the specific heat at the constant volume.) Calculate the final state temperature pressure p2.__________ (kPa)
The volume and temperature of a gas at the beginning of expansion are 0.0056m3 and 183°C, respectively; at the end of expansion the values are 0.0238 m3 and 22°C, respectively. Assuming expansion follows the law PV^n=C, find the value of n.
(b) A frictionless piston-cylinder device as shown in Fig. Qlb contains water at 400 kPa and the water is heated at constant pressure from saturated liquid to saturated vapor. Then, the heating process is continued in an isobaric manner until its specific volume reaches the value of 0.5 m²/kg. Water Heat Figure Q1b i) What is the initial temperature of water in the cylinder? ii) What is the final temperature of water in the cylinder? iii) Calculate the total boundary work during the processes, kJ/kg. iv) Calculate the total amount of heat transferred during the processes, kJ/kg. v) Sketch both processes on a T – v diagram with respect to saturation lines.
Water at P1 = 200 kPa with a quality of 25% has its temperature raised 20 oC (T2 = T1+20 0C) in a constant pressure process. What is the initial (v1) and final (v2) specific volumes?
A 2.80-mol sample of helium gas initially at 300 K, and 0.400 atm is compressed isothermally to 1.40 atm. Note that the helium behaves as an ideal gas. (a) Find the final volume of the gas. m³ (b) Find the work done on the gas. kJ (c) Find the energy transferred by heat. kJ
There is an 500g container made out of aluminum holding 300g of water. The Water and Aluminum have reached thermal equilibrium at 40 degrees Celsius. A 200g block of iron at a temperature of 0 degrees Celsius is later dropped into the water. Using the specific heat for water=4180J/kg/C. The specific heat for aluminum is 900 J/kg/C. The specific heat for iron is 450 J/kg/C. The final temperature of the three materials will be degrees celsius. The thermal energy of the water changes by Joules. (give an amount and include a + if it increases and a - if it decreases) The thermal energy of the aluminum changes by Joules. (give an amount and include a + if it increases and a - if it decreases) The thermal energy of the iron changes by Joules. (give an amount and unit and include a + if it increases and a - if the value decreases)
Could you please tell me whether 717.5 J is correct Answer or not (Don't copy ,Incase if you are unsure just skip it . I am confused with value ∆T ) Question 1: Consider a piston–cylinder device that contains 0.5 kg air. Now, heat is transferred to the air at constant pressure and the air temperature increases by 5°C. Determine the expansion work done during this process.
Shown in the figure, an insulated rigid tank is divided into two equal parts by a partition. Initially, one part contains an indeal gas, and the other part is evacuated. The partition is then removed, and the gas expands into the entire tank. At the initial state, the mass of the gas is m= 4.00kg, initial pressure is p1 = 600.00 kPa, initial temperature is T1 = 300.00 K. The gas constant is R = 0.2870 kJ/(kg·K). (The internal energy can be determined by the equation ΔU=m·cv·(T2-T1), where cv = 0.7180 kJ/(kg·K) is the specific heat at the constant volume.) Calculate the final state temperature T2.__________ (K)
3000 kJ of heat is given to 1 kg of water at 20 C. If steam with a pressure of 750 kPa is obtained as a result of this process, is this steam wet?institution? You should reach the result by typing the table values and operation steps. TIP: You should decide on enthalpy values using Thermodynamic Property Tables.
3-28 Complete this table for H₂O. T, °C 140 80 P, kPa 200 950 500 800 h, kJ/kg 1800 3162.2 X 0.7 0.0 Phase description
Shown in the figure, an insulated rigid tank is divided into two equal parts by a partition. Initially, one part contains an indeal gas, and the other part is evacuated. The partition is then removed, and the gas expands into the entire tank. At the initial state, the mass of the gas is m= 4.00kg, initial pressure is p1 = 600.00 kPa, initial temperature is T1 = 300.00 K. The gas constant is R = 0.2870 kJ/(kg·K). (The internal energy can be determined by the equation ΔU=m·cv·(T2-T1), where cv = 0.7180 kJ/(kg·K) is the specific heat at the constant volume.) Calculate the final state pressure p2.__________ (kPa)
A typical gasoline (β=0.00095/°C) tank can hold 65 liters (~17 gallons). At the gas station, the storage tank is underground and is maintained at a temperature of 50.0°F. On a hot day at 103.0°F you fill your empty tank. (a) What is the equivalent temperature difference in °C? A typical gasoline (β=0.00095/°C) tank can hold 65 liters (~17 gallons). At the gas station, the storage tank is underground and is maintained at a temperature of 50.0°F. On a hot day at 103.0°F you fill your empty tank. (c) How much gas should you put in your car on this hot day at so that it will fill (not overfill) the tank when it expands to 103.0°F?