Station A (10+040) 9.50 11 +3.00 +2.00 +4.00 Station B (10+060) 6.50 8.00 +1.00 1.20 +2.00

Q: Bar ABC has an outer diameter of 10 mm and is made of red brass for which E = 100 GPa. Section AB is…

A: Consider the BC portion of the beam:

Q: The uniform wire is bent into the shape shown and held by the frictionless pin at O. Determine the…

A: It is given that,

Q: The piece of rubber is originally rectangular. Calculate the average shear strain Yxy at A if the…

A: Given data in question Cross section 400 mm and 300 mmDisplacements 3 mm and 2 mmTo find out Average…

Q: Problem 2: For the following cross-section, compute l assuming the centroid of the entire cross…

A: It is asked to compute the Moment of Inertia, Ix for the given cross section  Given centroid of the…

Q: Given: Consider the following steel shape. 8 in H 1|2 in in 16 in Find: The value of S and Z and the…

A: Given: A T-shape cross section Required: Section modulus, plastic modulus and shape factor.

Q: For the non-symmetric Z-section shown in Figure Q4 find the position of the horizontal (X) and…

A:

Q: Determine the moment of inertia of the shape with respect to the left line

A: The given figure is as follows:

Q: For the beam cross section below, a vertical shear force Sz of 2,532 N is applied through the shear…

A: Shear force, P = 2532 N  Iyy = 8/3×a3×t   a = 108 mm    t = 4.3 mm

Q: Determine the Maximum Deflection of the beam in millimeters unit. Use the Virtual Work Method.…

A:

Q: The 16 x 22 x 25-mm rubber blocks shown are used in a double U shear mount to isolate the vibration…

A:

Q: Consider the rod shown. Suppose that hℎ = 170 mm, r = 290 mm. Determine the location (x,y)  of the…

A: The Centroid is the center of mass of the section of beam. It is considered as the center point of…

Q: The maximum deflection for the cantilever-beam below is no more than 0.03m.Macaulay’s method of…

A: Given:Cantilever beam with a length of 4 m.A point load of 50 kN at point C, 1 m from the fixed end…

Q: locate the centroid of the beam section shown

A: To Determine Centroid of the T-beam section.

Q: orce A=25 N A B=30 N

A: On the left side, tan(theta) = Perpendicular/base  tan(theta) = 7/4 = 1.75 angle theta = tan inverse…

Q: 2. Derive an equation that describes the vertical deflection of the beam, y(x), and also calculate…

A:

Q: 15 mm 15 mm 15 mm C

A: Divide the given section into three parts as shown in the below image: a = 210mm  b= 280mm c =…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: P=110 N

Q: The beam is constructed using 2 boards and 3 rows of nails spaced equally. A shear force is applied…

A: The moment of inertia

Q: The W10 x 15 cantilever beam is made of A-36 steel and is subjected to the loading shown in (Eigure…

A:

Length and Length related Variables

Length can de defined as the measurement or extent of physical quantities or objects from one terminal to another terminal. Stone age humans used finger length, step length, and so on to measure the size or displacement of an object. Nowadays, depending on how precise the measurement requires to be and the object’s size is measured, we use measuring devices for measurements like rulers and steel tape. Most people have used a ruler or tape measure to measure a particular distance or the size of an object. For more precise measurements of tiny objects, the development of measurement tools such as the Vernier caliper, which permits us to measure dimensions within 1/1000 of an inch. In the last few decades, electronic distance measuring instruments (EDMI) have been implemented that permit us to measure distances from a few feet to many miles with reasonable accuracy.