Answered: st punching if the total deformation of…

Engineering

Civil Engineering

st punching if the total deformation of the column is 0.72mm. Given below are the material properties.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

My student number is 202010237
An ASTM A615 grade 60 number 10 rebar with a gauge length of 8 in. was subjected to tension to fracture according to ASTM E-8 method. The load and deformation data were as shown in Table .Using a spreadsheet program, obtain the following:a. A plot of the stress–strain relationship. Label the axes and show units.b. A plot of the linear portion of the stress–strain relationship. Determine modulus of elasticity using the best-fit approach.c. Proportional limit.
1. The tensile strength vs. temperature curves of aluminum are plotted below. Explain the meaning of these two curves. 400 Ultimate strength 300 Yield strength 200 100 -200 -150 -100 -50 50 100 150 200 250 Temperature, °C Strength, kPa
Beam CX is subjected to a loading condition as shown on the figure. What will be (a) the maximum tensile stress and (b) the maximum compressive stress in Beam CX if its cross section is a T section with the given dimensions. 200 mm 160 kN 40 mm 100 mm --- 20 mm
Problem: In the composite section as shown in figure 1, determine the following.1. The value of x̄2. The value of ȳ3. The moment of inertia with respect to Neutral x-axis
(a) the modulus of elasticity in GPa for the Aluminum B) the proportional limit in MPa for the Aluminum C) the ultimate strength in MPa for the Aluminum D) Ductility of material based on percent elongation
As shown in the figure below, a bronze bar is affixed between a steel bar and an aluminum bar. Axial loads are applied at the positions indicated. If the largest value of P that will not exceed an overall deformation of 4.0 mm, or the following stresses: 150 MPa in the steel, 130 MPa in the bronze, and 90 MPa in the aluminum, determine the stress in the bronze. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. (The correct answer is 71.36 MPa. Can you show the solution? Thank you!)
A 3003-H14 aluminum alloy rod with 0.5 in. diameter is subjected to a 2000- lb tensile load. Calculate the resulting diameter of the rod. If the rod is sub- jected to a compressive load of 2000 lb, what will be the diameter of the rod? Assume that the modulus of elasticity is 10,000 ksi, Poisson’s ratio is 0.33, and the yield strength is 21 ksi.
Read the question carefully and give me right solution according to the options
A combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each Steel Copper Area, A 900 mm2 1,200 mm2 Modulus of elasticity, E 200 GPa 120 GPa Allowable compressive stress 140 MPa 70 MPa If the allowable strain for both materials is 0.0005, which of the following most nearly gives the maximum load the member can carry so that this allowable strain is not exceeded? Select the correct response 162.00 kN 185.00 kN 205.00 kN 175.00 kN
Mechanics of Deformable Bodies Show complete and detailed solution. Write legibly. Draw illustrations. Follow the decimals places on the direction
A 100 mm x 100 mm x 100 mm cube made with glass polymers in the y- direction is subjected to a tensile load of 100 kN along the y-direction. However, the cube is constrained against deformation in the x and z directions. Given the following properties: Ex = 20 GPa Ey = 50 GPa Ez = 20 GPa Vxy = 0.25 Vxz = 0.5 Vyz = 0.25 (a) Compute for the change in length of the cube in the y-direction and; (b) Determine the stresses, ox,Oy,Oz•