st definition of a conclus

Q: A line is recorded as 472.90 m long. It is measured with a 0.65 kg tape which is 30.005 m long at 20…

A: Solution; Given that; Distance measured on the ground , Dm=472.90 m Grade on which line is measured…

Q: 1. High Reynolds number flows are characterised by their slow rates of mixing and 'reversibility'.…

A: Note : Hi! Thank you for the question, As per the honour code, we are allowed to answer three…

Q: What can you conclude?

A:

Q: Isn't supposed to be negative? The final answer?

A: The magnitude of the point load = 950 N  The magnitude of the uniform load = 850 N/m The magnitude…

Q: 15. The following activities and times (in minutes) were recorded for a mold operator: I Removes…

A:

Q: 1. In a test to determine the discharge coefficient of a 50 mm by 12.5 mm Venturi meter the total…

A: Venturimeter is used to measure discharge into pipe. in venturimeter some loss is  occurred due to…

Q: If the wind velocity at a height of 2 m above ground is 5.0 kmph, its value at a height of 9 m above…

A: U2 = 5.0 Kmphh2 = 2mh9 = 9mU9 = to find

Q: 1. Which of the following is false? a) The density of water is dependent on temperature b) The mass…

A: Given data Conditions relating to fluid mechanics.  According to guidelines of bartleby I have to…

Q: The ratio of the Boussinesq's influence factor to Westergaard's influence factor at point 0 (2 m…

A:

Q: What does the variables stand for and assumption is valid ?

A: Stress strain diagram for singly reinforced beam

Q: Problem 20.5 The origin of the secondary coordinate system shown is fixed to the center of mass G of…

A:

Q: 20 kip 20 kip 4 kip/ft A B 15 ft- 15 ft 30 ft Ay = By Vmax= V Mmax-

A:

Q: Water discharging into a 10 m wide rectangular horizontal channel from a sluice gate is observed to…

A:

Q: The truss system below is in static equilibrium. a. Determine the reaction forces at A (pin support)…

A:

Q: 1. The wheel loads on a jeep are given in the figure shown.Determine distance x so that the reaction…

A: The free-body diagram is shown below,

Q: a) Mud is flowing through 4 % inch OD/ 3.64 inch ID, internal flush drill pipe. The circulating flow…

A:

Q: The side of the building in the figure is subjected to a wind loading as shown. The wind loading…

A:

Q: Determine the reactions at rigid supports A and B. A B →10 kN 1 m 2 m

A: Following is the given beam between two rigid supports:   Assuming reactions at both support acting…

Q: The diagram below is in static equilibrium. a. Determine all reaction forces at A (roller support)…

A:

Q: 7-6. Determine the equation of the elastic curve for the beam using the x coordinate. Specify the…

A: EI = ConstantDetermine the equation of the elastic curve, slope at A and maximum deflection of the…

Q: How to solve?

A: To find:The force denoted by F and the resultant force R.We have been given the following…

Q: The wall crane supports a load of 700 lb. determine the horizontal and vertical components of the…

A:

Q: Discuss the interaction between deductive and inductive reasoning in formulating the principles of…

A: Deductive and Inductive reasoning are the approaches that one can make use of in gathering the…

Q: (a) Explain and discuss structural plastic analysis approach and compare with elas or 'classical'…

A: in this question a discussion is being asked between plastic and elastic design

Q: The impeller of a centrifugal blower has an exit diameter of 0.6 m, B2 = 30°, and operates at 3600…

A: The question is based on the impeller of the centrifugal blower. The exit diameter, pressure at…

Q: 6 6-22. The beam is subjected to a uniform live load of 1.2 kN/m, a dead load of 0.5 kN/m, and a…

A: Given Span 16 mDead load = 0.5 kN/mLive load = 1.2 kN/m and 40 kNTo find out Maximum positive shear…

Q: Problem 4 Draw the load and moment diagrams that correspond to the given shear force diagram. Assume…

A:

Q: Water discharging into a 10 m wide rectangular horizontal channel from a sluice gate is observed to…

A: 1. Venturimeter dimensions: 5 cm × 2.5 cm2. Venturimeter coefficient of discharge: 0.983. Orifice…

Q: 7-10. Determine the slope at B and the maximum displacement of the beam. Use the moment-area…

A:

Q: Application of Empirical formulas?

A: The simplest notation of chemical formula is known as empirical formula.The chemical formula which…

Q: What are the basic characteristics of a linear model?

A: A one-way process is envisioned by a linear model of communication, in which one party is the sender…

Q: A. Differentiate between plain and reinforced concrete; why concrete is reinforced? B. What is the…

A: Question is based on concrete technology . In the question we have to differentiate between…

Q: Anaxial load Pis resolved into components A and B on an oblique plane as shown. Force is used in…

A:

Q: Which end use is largest consumer of energy in Canadian commercial buildings? Water heating Space…

A: The end use electricity usage is highest  water heating and space heating. But largest among these 2…

Q: What many types of information are taken into account while drawing a conclusion?

A: Conclusions are frequently regarded as the most challenging element of writing. However, they're…

Q: 13/ 12 B -2 m 4 m

A: solution  The weight of homogenous bar acts at the center of the bar i.e at 3 m form point A Draw…

Q: Given the SDOF system is disturbed by an initial velocity of 3 m/sec, determine forces in column AB…

A: Initial Velocity = 3m/sec E = 20684 cm4 I = 6939 kN/cm2

Team Management

To complete a specific task or to accomplish organizational goals along with increasing work productivity, individuals need to come together and think along a common path and direction. There are certain tasks in an organization that cannot be done alone and the involvement of more individuals is essential. These groups of individuals who work together for a common goal compose a team and the individual members involved are known as team members.