spring-mass system with m = 0.01 Mg and k= 5 kN/m is subjected to a harmonic force of amplitude 0.25 kN and frequency wo. If the maximum amplitude of the forced motion of the mass (particular solution or steady state) is observed to be 100 mm, find the value of wo

Q: 8(s+5) Y(s) s'+10s +16s +40 vibration of the mass m caused by the displacement of the foundation,…

A: 8×s+5s3+10s2+16s+40×0.05s3+5 X(s) is given above plot of response -

Q: A 1.5 kg mass is attached to a vertically oriented spring, stretching it 0.45 m. The mass is moved…

A: Solution: After adding a mass of 1.5kg the spring is stretched to a equilibrium position that is…

Q: The tip of a massless clamped-free beam connected to mass m = 2 kg by a spring with stiffness k =…

A: The mass of the block, The stiffness of the spring, The mass is excited by the force, The Young's…

Q: A 120-kg machine is placed at the midspan of a 85-cm aluminum (E = 100 x 10°) N/m² simply. supported…

A:

Q: Two mass placed on top of each other have a mass of 20 g each and there is a coefficient of static…

A: At the position of amplitude the restoring spring force will be F=kAand therefore the acceleration…

Q: A precision grinding machine is supported on an isolator that has a stiffness of 3 MN/m and a…

A:

Q: An electric motor of mass 68 kg is mounted on an isolator block of mass 1200 kg and the natural…

A: Given 68 kg mounted on 1200kg m=1200+68=1268kg wn=160  rpm=160×2𝜋60=16.75rad/s F=1005m, w= 31.4…

Q: A machine of mass 170.8 kg is mounted on four parallel springs each of stiffness 2.2 x 105 N/m. When…

A: The given values are -  m =170.8 kg , k = 2.2x105 N/m , f=57.5 Hz , A = 1.4 mm It is also given that…

Q: Consider the mechanical system shown below with a dash-pot (the dash-pot produces a friction force…

A:

Q: An electrical switch gear is supported by a crane through a steel cable of length 4 m and diameter…

A: Given data: L=4 md=0.01 mT=0.01 s Need to determine the stiffness of the cable.

Q: 3.5. A spring-mass is excited by a force F, sin ut. At resonance, the amplitude is measured to be…

A:

Q: has a stiff us damping A precision grinding achine is supported on constant of 4 kN-s/m. The floor…

A: The stiffness is k=2 MN/m=2*106 N/m. The viscous damping constant is c=4 kN-s/m=4*103 Ns/m. The…

Q: in undamped simple harmonic oscillator has mass 2.0 kg and spring constant 5 /m. The initial…

A:

Q: Find the natural frequencies of the system for k₁= 250 N/m, k₂ = 700 N/m, k3 = 100 N/m, m₁ = 1.8 kg,…

A: Given: The stiffness of spring 1, K1 = 250 N/m The stiffness of spring 2, K2 = 700 N/m The stiffness…

Q: 3.5. A spring-mass is excited by a force F, sin wt. At resonance, the amplitude is measured to be…

A:

Q: A machine of mass 112.7 kg is mounted on four parallel springs each of stiffness 3.2 x 105 N/m. When…

A:

Q: A machine of mass 203.5 kg is mounted on four parallel springs each of stiffness 1.6 x 105 N/m. When…

A: Introduction In this problem, we will calculate the magnitude of the force transmitted to the…

Q: A block of mass m hangs from a spring with a spring constant k. The block is initially held so that…

A:

Strain Gauges

All the components used in civil engineering and mechanical engineering applications undergo deformations due to induced internal stresses under the application of external loads. Under repeated application of loads, there is a high possibility of failure of the components. Hence, periodic monitoring of the components and determination of stresses are very important.