Specify a suitable orifice meter run for measuring 100 MMscf/day of GOM production sale gas entering the run at 1200 psia and 120°F. Use reasonable water differential pressure and pipe. Include run length, orifice size and run diameter. Assume there are no valves in the run proper.

Q: 2. Explain in short major engineering difficulties in water treatment process

A: This question is based on water treatment process and the engineering difficulties associated with…

Q: Which pump is an integral part of the petrochemical and edible oil factory? What are the use of this…

A: There are a lot of pumps used in petrochemical and edible oil factory like positive displacement…

Q: A cast iron pipe (L=400 m, D=150 mm) is carrying 0.05m/s of water at 15 °C. Determine the loss due…

A: L= 400 m Q = 0.05 m³/s e= 0.26 D = 150 mm e/D = 0.00173 Hence, friction factor, F = 0.024

Q: 7. Determine the number of sprinkler heads required to protect an inside process area of 2000 ft².…

A:

Q: 1. Pumps and its types 2. Pipelines 3. Tanks

A:

Q: Following is the example of. O a. Orifice meter O b. Flow O C. Flow Pressure meter Rotameter

A: In the given image, the device contains a transparent glass tube that is placed vertically.  In this…

Q: A solid cylinder of weight 9 kg slides in a vertical lubricated pipe. The clearance between the…

A:

Q: The computed stress should be lower or equal to the allowable stress for the material to be safe in…

A:

Q: A centrifuge bowl is spinning at a constant speed of 2000 rpm. The radius of bowl in cm needed to…

A: Given that N =2000 rpmwe have to find radius of bowl in cm when there is needed to create a force of…

Q: Why does the fluid drop in the fluid level measurement experiment when the pump is turned off?

A: In a typical fluid level measurement experiment, the pump is used to recirculate the fluid in a…

Q: 3.) A steel bar 100 mm long and having a square cross section 20 mm on an edge is pulled in tension…

A: Given: Length of steel bar=100 mm=100×10-3mCross section of the steel bar=20 mm=20×10-3mForce=89000…

Q: In tillage operations, the typical required draft per unit width of implement for a clay soil is 5…

A: The wdth and draft width are used to obtain the total draft. The width is considered in units of…

Q: • Air at standard temperature and pressure flows through a horizontal, galvanized iron pipe…

A: Air flows through the galvanized iron pipe at standard temperature and pressure. Volumetric flow…

Q: Write a report detailing the energy balance in pumps, with illustrations, formulas, and diagrams and…

A: A pump is used to move liquids with the help of the pressure difference between one point and the…

Q: what is the actual air required per hour.

A: Ultimate and proximate analysis of the coal sample is given. Flow rate of coal = 11762 kg/h % Excess…

Q: 3 - What is the energy equation used in orifice meter? 4 - Define vena-contracta?

A: Energy equations work on the principles of conservation of energy.

Q: When using an aspirator as a source of vacuum in a vacuum distillation, do you turn off the…

A: It is to be mentioned if the aspirator is turned off before venting the system or not.

Q: Compare S.I and C.I engines with respect to fuel used

A: CI engine - Compression ignition engine SI engine - spark ignition engine

Q: Baffles increases the fluid velocity on the tube side. True False

A: Baffles are used to direct fluid across the tube bundle and run perpendicularly to the shell.…

Q: 2 - What is the use of orifice meter?

A: The flow of fluids is based on density, viscosity, flow rate, etc. These flow rates are measured…

Q: As flowmeters, these devices are most widely used. They most often also have ★ integral temperature…

A: As flowmeters, these devices are most widely used. They most often also have integral temperature…

Q: 5. Rods AC and BC are used to suspend the 200-kg load. If each rod is made of a material for which…

A:

Q: Reynolds analogy is preferred over Chilton-Colburn analogy. O True False Depends on Sh O Only for…

A: Chilton Coulburn analogy is widely successful analogy used for estimating mass transfer…

Q: Criticize why this situation happens.

A:

Q: A solid 0.6-in.-diameter cold-rolled steel rod is pinned to fixed supports at A and B. The length of…

A: Given data: Diameter of rod = 0.6 in Length of rod = 22 in Elastic modulus = 29000 ksi Coefficient…

Q: Calculate the pressure gradient due to gravity in water, in psi/ft. Most experienced engineers round…

A: The pressure gradient due to gravity in water is calculated as follows:Determine the density of…

Q: Nitrogen gas has a heat capacity of 20.8 and 29.1 J/mol-C at constant volume and constant pressure…

A: Given Cv = 20.8 J/K.mol Cp = 29.1 J/K.mol Initial temperature = 50K Final temperature = 100K Find…

Q: Two flocculator treat 1.2 m/s and remove flocs large than 0.02 mm. The settling velocity of the 0.02…

A: Given data: Volumetric flow rate = 1.2 m3/s Width of settler = 50.8 mm Angle = 45 0 Vertical height…

Q: Which of the cross-sections below would experience the lowest engineering stress when the same load…

A: Engineering stress is defined as, Engineering stress = Force appliedcross-sectional area let us…

Q: Assume that the 5-in. valve with Cvmax = 500 is selected and that the pressures around the valve are…

A: The flow rate considered for the valve is gallons per minute. The rangeability parameter represents…

Q: 3. What factors should we take into account for the selection of the pipe size and design of the…

A: 1. Material: Pipe material assumes a vital part in deciding the quality and tension of compacted…

Q: A centrifuge with a bowl which is 500 mm long and has an inside radius of 50.5 mm is to be used to…

A: Given : Bowl length Bowl radius Rotation speed Liquid depth Crystal diameter

Q: 8 ft 7 ft 10 ft 45° entry 10 ft 10 ft A B 3 ft 3 ft

A:

Q: Repeat Example 7.7 for 3-in schedule 40 pipe with water flowing at 8 ft/s and pressure 30 psig…

A: Given,

Q: adiabatic turbine

A:

Q: AU-tube manometer contains oil (50 Ibft3), mercury (849 847 Ibf/ft) and water (62.4 lbf/ft). For the…

A:

Q: Exercise 1: Convert -0.916 V (on SCE. 1.0 N) to the SHE scale.

A: To convert -0.916 V on SCE 1N to SHE

Q: 12. Write the material balance equation for single stage co current and countercurrent processes

A: 1) Single stage process is a unit operation used for the separation of two fluids mostly liquids…