Solved: Write a program to implem... www.chegg.com • The agitate motor starts automatically and runs for 3 min to mix the liquid. When the agitate motor stops, solenoid B is energized to empty the tank. • When the tank is completely empty, the empty sensor switch opens to de- energize solenoid B. • The start button is pressed to repeat the sequence. Motor ← = Chegg Figure 7-46 Process for Problem. SOLA Empty sensor switch Full sensor switch SOL B Start/stop control station

Q: In the simple lamp dimmer shown here, what method of power control is being used? LAmP AC supply…

A: The figure shows a lamp dimmer circuit, this circuit uses the DIAC and TRIAC combination for the…

Q: Explain how the wind drives the blade of a wind turbine

A: Wind turbines are tall structures that consist of tall towers mounting a blade that rotates due to…

Q: What is clamper? Briefly explain its working.

A: We neec to tell about clamper circuit . We need to draw the circuit diagram and output waveform for…

Q: Choose the correct statement below motors are actuators but not transducers DC motors and servo…

A: The actuator generates motion in the system by changing the electrical energy into mechanical. The…

Q: Directions: DRAW and label the parts of an Electric Motor. In your own words and idea, write a short…

A: Electric motor: It is an electromechanical device that takes electrical input and produce the…

Q: Explain with figure forced circulation solar water heater.

A:

Q: 1. According to the working principle, there are three types of capacitive sensors, of which ( ) is…

A: Capacitance of a capacitor is depends on Area of plates Distance between plates  Material in…

Q: What is lightning? Describe the mechanism of the lightning discharge.

A: Lightning- It is a discharge of electrical energy of very short duration and high voltage between a…

Q: a)Why is the fluorescent circuit economical, and how do we calculate the power of the lamp and how…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: 22. a) Describe how the following sensors are used to measure temperature. i) RTD

A: Any system can be autonomous or manual. A system is called autonomous if the output is independent…

Q: The electrical energy that is produced will be a part of the. energy applied to rotate th The number…

A: To fill up the blanks

Q: 4- A 100kW, belt driven shunt generator running at 300rpm on 220V bus bars continue to run as a…

A: Generated emf = terminal voltage +voltage drop in armature resistance +brush voltage drop. Back emf…

Q: What are the advantages of electrodynamic instrument, remind only four

A: given electrodynamic instrument

Q: Q1: An armature has a resistance of 0.4 Ω at 120°C and the armature Cu loss is to be limited to 500…

A:

Q: Figure Q1(a) 100 Ka 20 Ka 10 Ka + 30V I Ka PC R, 0.1 Ka 1 10 100 1000 Im/m 400 ILLUMINATION (a) (b)…

A:

Q: Assume the fan motor is equipped with a thermal cutout designed to interrupt the motor circuit ifthe…

A: consider source 1 and source 2

Q: Why is high pressure needed in HPLC?

A: HPLC is a high -performance liquid chromatography which are basically upgraded type of column…

Q: Explain the following picture and its' importance in selection of circuit breakers. Extinction of…

A: to explain the following picture and its importance in selection of circuit breakers

Q: If the voltage across a DC motor is -105 V and is fed from a fully controlled rectifier supplied…

A:

Q: Explain all part and its working in motion control lamp diagram

A: One can use motion sensors to automatically turn on a light when someone approaches in home. In this…

Q: Compare between servo motor and universal motor

A:

Q: method of heat transfer principle is used to monitor changes in temperature in non contact type…

A: The solution is provided in the following section:

Q: What does balance modulator generate and what does it eliminate.

A:

Q: How long a wire is needed to coil a spring having a mean diameter of 1 inch if there are 8 active…

A: Given, A spring has a mean diameter. d = 1 inch Total number of coils, n = 8

Q: Make a circuit to control the 3-phase AC motor, such that it will turn on when the on button (NO) is…

A: Make a circuit to control the 3-phase AC motor, such that it will turn on when the on button (NO) is…

Q: Explain how a direct online (DOL) magnetic starter works with diagrams and pictures

A: We are asked to explain direct online (DOL) magnetic starter.

Q: What are the different types of temperature sensors? Explain the construction and working of…

A:

Q: Figure 3 illustrates a thyristor phase control circuit and associated waveforms. Describe the…

A: Thyristor:- It is a four-layer power electronics device. A gate, a cathode, and an anode are the…

Q: Statement below are true about limit switches except:- a. Limit switches is also called as…

A: Statement below are true about limit switches except:- a. Limit switches is also called as…

Q: is the amount of change in the controlled variable required to run the controlled device from one…

A:

Q: What is the mechanism of operation motion control lamp

A: mechanism of operation motion control lamp:

Q: A DC drive is fed from a fully controlled rectifier supplied from a single-phase supply of 240 V, If…

A:

Q: What is an example of inertial sensor

A: The sensor is an important part of the design which takes or sense physical signal like motion,…

Q: Determine the value of R1 that will ensure proper turn-on and turn-off for the following values: eta…

A:

Q: 4. Complete the program at the right for controlling robot according to sensor status M. Left M…

A: The program for controlling the robot according to sensor status is shown in step-2.

Q: (a) State the types of turbine flow meters and point out the difference between them.

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Motor Load, Torque, and Power Quality Requirement

An electric motor is a gadget that changes electrical energy into mechanical energy over to follow up on a mechanical burden. The weight set on the motor because of this mechanical movement is known as motor load. Appropriately matching the motor burden to the engine is vital to forestall harm to the engine or wasteful and unnecessary expensive activity. Engines perform such undertakings as moving a thing starting with one spot then onto the next, cutting it, changing its shape, etc. The motors might be evaluated as far as a few variables including power yield, voltage, current, and temperature. Harm to an engine might happen when it is worked under over the top engine load contrasted with its appraised limit.