Solved Examples Example 5 Replace the force and couple moment system acting on the beam in the figure below by an equivalent resultant force, and find where its line of action intersects the beam, measured from point O. 15 KN m asm Solution:- Force Summation. Summing the force components, 15m+15m 15m 15m

Solved Examples Example 5 Replace the force and couple moment system acting on the beam in the figure below by an equivalent resultant force, and find where its line of action intersects the beam, measured from point O. 15 KN m asm Solution:- Force Summation. Summing the force components, 15m+15m 15m 15m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the loading system shown below, replace the loading by a single force and a moment at D What is the vallue of the moment? No decimal digits are needed Take F1 81 N, F2= 191 N, F3 = 243 N, and MC = 191 Nm F2 1m 2 m 3 m B 2 m Mc 60 3m F1
I need quick solution, attempt only if you can solve it fast. Answer is around 166.7lb (don't know where on the beam does the resultant acts) Show work with FBD
1-4 4) Find the magnitude and direction of the resultant force and moment at point A 3.6' 4.4 150lb 3.6 150lb FORCE e F, =F.Cos(e)F, =F.Sin( e) (Ib) M, =Fxd FORCES COUPLES RyF RESULTANT FORCE AND MOMENT DIAGRAM 165lb 165lb 200lb
1 ft 3 ft B 3 ft 3 ft (-9002 + 800f + 1000k) Ib.ft 6 ft 3 ft E (-300î – 400ĵ + 100k) Ibs The applied force at point E and the applied couple moment at point D are shown in the figure. Complete/calculate the following: (Where applicable, express the results as the (x, y, z) components of a Cartesian vector) 1. Draw the free-body diagram (FBD), showing the appropriate reaction forces and/or moments at the supports. (You must show the reactions in their component form i.e. show RAx, MRAX etc. on the FBD). Note: The support at point A is not able to resist a moment about the 'X' axis but is able to resist a force in this direction. 2. ME, which is the moment vector at point A due to the force acting at point E 3. Me, which is the moment vector at point A due to the tension force acting at point B. Write the vector in terms of the unknown tension magnitude 'T' 4. Set up the equations of equilibrium (You must show all relevant equilibrium equations one below the other. 5. Calculate the…
A spring is attached to points A and B as shown in the figure. The spring constant, k, is given equal to k = 100 N/m and it is stretched by s= 0.1m. Distance b = 2 m. 1. Consider the force which the spring exerts on point A only and calculate the moment it produced about point 0. 2. Calculate the moment produced by the same force about axis z. 1.56 B F 6666666666 b b -y
Use the graphical method to construct the bending-moment diagram and identify the magnitude of the largest moment (consider both positive and negative). The ground reactions and the shear-force diagram are provided. M = 13 kN-m Ay = 3.46 KN Dy Units: KN = 32.54 kN M 4 m 29.5 kN-m 43.3 kN-m 25.8 kN-m O 22.9 kN-m 31.48 kN-m B Ay 4 m 15 kN C Ay 4 m Ay-15 7 kN/m D 3 m 21 Ay-15 E X
Replace the force system on the post by an equivalent resultant force and a couple moment MR at point c .also find the angle of tge resultant from point C
Using the image below replace the distributed loading with an equivalent resultant force, and specify its location on the beam measured from point A. Let the length be: L1 = 9 ft. Let the loads be: W1 = 70 lb/ft, W2 = 420 lb/ft. Note you must determine the coefficients a and b based on the given intensities of the loads W1 and W2, respectively.
A simply supported beam is loaded as shown below. In the first region, the distributed load linearly increases from 0 kN/m to 15 kN/m. In the second region, the distributed load linearly decreases from 15 kN/m to 0 kN/m. What is the moment that this distributed load creates about point A in kN-m? W A 1m 1m 1m B
Finding the bar forces by the nodal point method
PLS DO STEP BY STEP PLS DONT TYPE ,WRITE ON A PAPER STEP BY STEP SOLUTION, APPRECIATE UR HELP
P{lease don't provide handwritten solution ..