Solve for VR1 and IR1. Using any dc circuit theorem.

Q: 2.-(33) Using a (PUT-PUJT-UJT) design a timer that hos period of Imsec. a

A: It is asked to design a timer with a period of 1 ms by using a (PUT - PUJT - UJT).

Q: IV) Explain the operating principle of a dual-slope ADC circuit, in your own words

A: ADC (ANALOG TO DIGITAL CONVERTER)- It converts analog signals to digital signals. ADC signals are of…

Q: The current and voltage waveforms given in the figure on the right. power electronics converter to…

A:

Q: discuss some design specification of a typical outlet.

A: Electrical outlets 15-amp duplex receptacles are the most popular electrical outlets; 15-amp outlets…

Q: 1. Loading error estimation: as we use voltmeter to measure the voltage drop across a resistor Ro,…

A: The given circuit diagram is shown below. Load error is introduced by the incorporation of the…

Q: Q1) Compare between the Top-Down and Bottom Up Desigr note: your comparison should contain the…

A: As per our policy we would answer the one question .If you want remaining pleases repost them as…

Q: The module MSX-83 from BP solar is used in the following configuration to make a PV array: • 4…

A: Explanation: Given that, for a single module Short-circuit current (ISC) = 5.27 A Open-circuit…

Q: Identify a true statement about time domain. -It refers to displaying or expressing a signal as a…

A:

Q: what is the implementation of the load flow analysis

A: Load flow analysis, also known as power flow analysis, is a crucial component of electrical power…

Q: iii) Explain the operating principle of a single-slope ADC circuit, in your own words

A: The ADC is an analog to digital convertor. The machines understand the digital binary bits in their…

Q: Explain the environmental impacts of wind power plant?

A: Same as all other power generating systems, wind power generation system also have many unfavorable…

Q: What is a clipper circuit? Draw an example circuit diagram, including component values, an input…

A: Clipper circuits:  These circuits are the circuits that are used to clipping the input waveforms. In…

Q: 2. When a large shunt capacitor is suddenly connected in parallel with the load bus in the…

A:

Q: can we use a non-linear device as a DSB-SC demodulator? Suggest a diagram.

A: The process of extracting an original message signal from DSBSC wave is known as detection or…

Q: 1.28 For the following peak or ms values of some important sine waves, calculate the corresponding…

A:

Q: When connecting resistors in series, discuss: 1_ To make the voltage equal on all the resistors,…

A: Introduction Ohm's Law: According to Ohm's law, provided that the conductor's physical…

Q: Exp. 2/DC sputtering: 1- Explain the main principles of coating by DC-sputtering technique with…

A: Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Electrical Engineering Compare Eucidean distance and cosine similarity. When to use them for…

A: Without formulating a specific hypothesis, clustering is an undirected approach used in data mining…

Q: Rs 100 N Vs iB Vs = Vs + Vs RL = 1 kN VL = VL + v1 %3D + Biasing Component Vs = 6 V UB + 5 1

A: We need to find out unknown resistance value and Gain for given circuit

Q: Voltage-divider biased, npn BJT with 1. VCC = 22V 2. R1 = 39kohms %3D 3. R2 = 7kohms 4. RC = 4kohms…

A:

Q: USE APPROXIMATE ANALYSIS USE 2 decimal places, no commas. Given: Single-stage, voltage-divider…

A: The required parameters can be calculated by using DC and AC analysis of the amplifier circuit

Q: *. 2 6-5-4-3–2-1 567

A:

Q: V* = 18V Cc Rs Rp V=-18V

A: Given: VTP=-1V ,VTN =1V ,KP =1mA/V2 , Kn=2mA/V2 ,Rin=100K ,IDQ1=3mA , IDQ2=5mA , VSDQ1=5 V ,…

Q: a) An SCR based AC power controller circuit is given in Figure 1. The circuit connects a 240V 50Hz…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: A highly inductive load, such that load current can be assumed constant, is to be supplied from a…

A: Here, we have to calculate the output voltage produced by the fully-controlled and a half-controlled…

Q: which the voltage regulation is maximum and the value of this regulation.

A:

Q: What is non linear modulation?Explain with example?

A: Modulation: Modulation is the process of in which information from a message source is encoded to…

Q: 06) Consider the circuit shown in figure 5, assume that V Q6a) ID(en) (in mA) is: A) 0.02 B) 2 C)…

A: The circuit diagram is shown below, Where,RD = 4kΩandVZ =8 V

Q: For a system if the value of peak overshoot is 26 %,  then the value of damping ratio  is .......

A:

Q: In transfers characteristics of JFET   ID=IDSS{1- [VGS/VGS(OFF)]}² Is this come by calculating…

A: In transfers characteristics of JFET   ID=IDSS{1- [VGS/VGS(OFF)]}² Is this come by calculating the…

Q: What are Low voltage network types? And explain every type of it ?

A: A low-voltage network is a component of electric power distribution that transports electricity from…

Q: Provide brief answer only. What is a variable DC source? Give symbol and applications.

A: Variable dc source is an Electrical/Electronics device which is used to supply the variable DC…

Q: Analyse several voltage and current situations in different loading scenarios in a simplified radial…

A: Reflection on the Complexity of Calculations:The complexity increases with:Voltage-Dependent…

Q: Sketch a step response for a second-order system that displays considerable overshoot and ringing.…

A: Given: To sketch a step response for a second-order system that displays considerable overshootand…

Q: Q1: a- Explain the following briefly: 1- Gray box model 2- black box model 3-causality. b- Prove…

A: The time domain signals can be continuous or discrete. The time domain signals can be periodic as…

Q: 1. Why sub transient current magnitude is large compare to steady state current?

A: In power system transient and sub transient current it is occur only when three phase fault occur in…

Q: Draw a 5-stage cascaded voltage multiplier circuit for the generation of HVDC and explain the…

A: What is a voltage amplifier? Voltage multiplier is a kind of rectifier (AC to DC) circuit which…

Q: What MPPT algorithm helps in pv optimization

A: PV(photovoltaic) Photovoltaics uses semiconducting material to convert direct light into…

Operational Amplifier

An operational amplifier also called op amp is an integrated circuit or analog circuit that takes input as a differential voltage and produces output as a single-ended voltage. It is an IC that can amplify weak electric signals.An op amp has one output pin and two input pins. The basic role of an opamp is to amplify the voltage difference between the two input voltages. It is also used in filtering or to perform mathematical operations or in signal conditioning.