Solve for the force in member BF using method of sections and method of joints. 12m 2000N 12m F 8M 8m 3000N 1500N

Q: Given in the accompanying sketch is a cross-section which has been plotted from soundings taken…

A:

Q: Problem No. 2: Determine the x and y-coordinate of the centroid of the shaded area.

A:

Q: Q1. Figure shows a cross section view of a structure. All dimensions are in mm. (a). Determine the…

A: Solution: Given:

Q: The mass of the suspended object is m = 60 kg (Figure 1) Figure 0.6 m -0.8 m 0.2 m -0.6m- 0.2 m m 1…

A:

Q: Convert the following distances given in feet to meters: Part A 521.80 sft Express your answer in…

A: convert the following distances given in ft to meters :-Part A)521.80 sftPart B)2100073.9 sftPart…

Q: 1)Given the following set of stadia level notes. The instrument used has a stadia interval factor of…

A:

Q: Instructions: Solve the following problems. Show your complete solution and illustrations. Box your…

A: Normal stress is σn=12 ksi. Shearing stress is τ=14 ksi. Bearing stress is σb=18 ksi. Based on…

Q: Calculate the shape factor of the cross-section shown. 200 12 250 600 50 50 700

A:

Q: Fill in the following Leveling Notes. In your handwritten notes, perform a page check and calculate…

A: Surveying is a very important branch of civil engineering as it is mainly dealt with the measurement…

Q: Problem #3: Note: Replace all zero digits of your ID number by number "2" F1= 40 + A (N) Use X =…

A:

Q: х (N) C A (m) - 2 m 2 m- A 60° 11. Determine the horizontal reaction at A. (N) 12. Determine the…

A: X = 175 A = 9

Q: 7. PROFILE file of pro- level notes and show the customary arithmetic check. LEVELING. Complete the…

A: Given: The differential leveling notes are given below, STA BS HI FS IFS ELEV BM-0…

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: * aut cad Ray is one of the commands for the drawing list. It is used to draw a ray, using two…

A: Explanation :  Ray  command in AutoCAD  is used to draw rays from a starting point in a perticular…

Q: an object moving horizontally after t seconds is given by the it3 +36t2-54t, where s is measured in…

A:

Q: Given the fence 20 meters long and 3 meters high, determine the total number of pieces of 10 mm…

A: ASSUME SPACING OF VERTICAL BARS= 0.4 METER

Q: d t (consta nt thicknes s) b Area (xbar) Ixo lyo ly NA 1- = 11 in 0.3 in 4 in 3.300 in2 1.495 in…

A:

Q: QUESTION 8 What is the flow of a pipe that has an 8" diameter and 1% slope? Use the Hazen Williams…

A: dia of pipe=8''slope=1%=0.01discharge=?

Q: You are a professor of architecture. Show your students where the horizon line and vanishing points…

A:

Q: And

A: In summary, the first fundamental theorem of calculus establishes the relationship between…

Q: As figure shown, there are 2 orifices both end and has 0.20 square meter. 30 meter long and 8 meter…

A:

Q: ↑v-axis J- Figure for Problem 2 Note: Each square indicates 1 square unit (0,0) х-ахis

A:

Q: Please

A:

Q: How to draw a free body diagram please.

A: As per guidelines we need to answer only first question so please repost rest questions separately

Q: 8. On a map of scale 1:75,000 the map distance measured between points A and B is 5.0 cm. If a…

A: Solve question 8 and 9

Q: The section comprising of two 250 x 37 channels shown was built-up in such a way that their…

A:

Q: blem #1: в (m) 800 + A (N) 200 + Y (N/m) 2 m 60° B Determine the horizontal reaction at A. (N)…

A: 1. Determine the horizontal reaction at A.  2. Determine the reaction at A. (N) 3. Determine the…

Q: Answer the following four questions for the following information Time (min) Discharge (m³/s) disch…

A: The table given is of flood hydrograph. Since at the end and beginning of the observation flow is…

Q: Draw the flowchart to calculate the area of ​​the two shapes and print the smallest of them

A: Using rectangular area calculation (a X b) Rectangular area is calculated, similarly using isosceles…

Q: A 40 SITUATION 6

A:

Q: Calculate the end areas for depths of fill from 0 to 20 ft using increments of 2 ft for level…

A:

Q: Fill in the blanks Smaller angle: Larger angle: s = 20 ft Determine the two possible angles so that…

A: Determine the two possible angles so that the water strikes at B.?

Q: Please calculate the centroid x and y bar, and Ixx for the following shapes. Show all work with neat…

A: ## Understanding the Problem**Problem:** Calculate the centroid (x̄, ȳ) and moment of inertia (Ixx)…

Q: Please recheck and answer in 3 decimal places.

A:

Q: a. b. C. d. ÏÏ The most important If a mistake is found Regarding surveying having too much…

A: There are three main sources of error arise: 1) Natural error - climate, wind, humidity etc. 2)…

Q: The left and right water edges of a river are 3.75m and 65.25m, respectively, from an initial…

A: Area Velocity Method- This method is used to measure discharge in the river. It is generally…

Q: What are the geocentric coordinates in meters of a station which has a latitude of 50°25'33.71631"…

A: ϕA=Latitude of station=50°25'33.71631''NλA=Longitude of station=121°49'53.68672''WhA=Height of…

Q: 1. Determine the centroid of the hallow in the figures show. Enclose your answers in a box. 12" 0|…

A:

Q: What is the importance of knowing the material specification in plumbing design?

A: Any type of building like residential or commercial or industrial, can't function properly without…

Dimensional homogeneity

The term dimensional homogeneity means that in an equation, the dimensions of each term on both sides are equal, which means the dimensions of the left-hand side (LHS) of an equation are similar to the dimensions of the right-hand side (RHS). For a dimensionally homogeneous equation, the powers of fundamental dimensions will be identical on both sides of the equation.