- Soil Compaction '1. A series or Modilied Proctor Tlests have been perfomed on a soil that has a unit weight of 26,290.8 N/m³. The volume and mass of the empty mold are 1/30 ft and 1.970 kg, respectively. The test results obtained are as follows: Moisture Content Test Results Point No. Mass of Mass of Can Mass of Can+Moist Mass of Can + Compacted Soil+Mold (kg) (g) Soil (g) Dry Soil (g) 1 3.673 22.11 205.74 196.33 3.798 23.85 194.20 180.54 3 3.927 19.74 196.24 177.92 3.983 20.03 187.43 165.71 3.932 21.99 199.59 171.11 b. Determine the MDD and OMC based on the modified Proctor Test. Express your answers in two-decimal places. Show complete solution.

Q: A is an electronic file that contains numerous projects within it. O project pool WBS Gantt chart…

A: Project Pool means a series of Eligible Projects sold to Owner XVII or Owner XVIII in accordance…

Q: Why is the contractor, required to submit all data through the field office and not directly to the…

A:

Q: What is the overall density? %

A: This question is related to the Soil Mechanics from Civil Engineering.

Q: Add/Subtract the following DMS measurements by hand. In your answer, separate each unit by a comma…

A:

Q: How many "varas" are there in a single ruler measurement?

A: A single ruler is the standard ruler which has measurements given in inches or mm. It is used to…

Q: show the integration process

A: To show the integration process

Q: Reading Settlement Settlemen Specimen Avarage Specimen Height (h) Stress AH/h Stress Different…

A: Stress Range (KPa)   Stress different∆p(KPa) Reading  Settlement      (mm) Settlement…

Q: Could you show the calculations for the table

A: The discharge through the section = Q = 100, 150, 200, and 250 cfs The slope of the section = S =…

Q: Engineers may accept outside work without notifying their primary employer. True False

A: Brief concept- There are certain ethical codes of conduct according to which the work should be…

Q: Give specific examples of potential unnecessary costs identified in items 1-5 below on value…

A: Note- Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

Q: What are National New Source Performance Standards (NSPSs) ?

A: Brief Introduction- National New Source Performance Standards (NSPSs)- These are pollution control…

Q: A triangle has an area of 14 sq ft and a base of 7 feet. What is the height of thetriangle?

A: given data :  area of triangle (A) = 14 square feet  base (b) = 7 feet  height (h) = ?

Q: In detail what is the CSI MasterFormat and what is listed in division 28?

A: Answer  CSI MasterFormat also known as "Dewey Decimal system" is the product of the Construction…

Q: Define Weight-Volume Relationships

A: The weight volume relationship is depicted in following properties:- Void ratio:- The ratio of…

Q: how did you get 1.5 for the first part

A: In the original question it is stated that Vmax=2 Vmin In the solution, the following is given.…

Q: What are Xrefs and its applications?

A:

Q: What is the area of 6 #8 bars in inches^2? Give an answer to two decimal places.

A:

Q: Name 3 major stages in Design phase of a construction project

A: The objective of this question is to identify and describe the three major stages in the design…

Q: Under CSI Format, explain the difference between the documents referred to as “General Conditions”…

A: Difference between the General conditions and general requirements under the CSI format:

Q: actors that cause hardness along with a bibliography

A: The water hardness may be simply defined as the amount of dissolved calcium and magnesium in the…

Q: some examples of the term OFFSET

A:

Q: Define the following, (i) Data set (ii) Attribute (iii) Measurement scale.

A: Given data: Define the following, (i) Data set (ii) Attribute (iii) Measurement scale.

Q: Describe the Project Delivery System?

A: The project delivery system is a process which is used to assign the responsibilities of the…

Q: What is expert determination?

A: Experts are often assigned by justices and adjudicators in national courts and arbitration…

Q: Figure 2

A:

Q: Discuss the safeguard measures of a contractor.

A: The contractor is a person who looks after the safety of people at construction site. The contractor…

Q: For the following scale calculate the equivalent ratio scale 2inches represents 48 meters

A:

Q: Describe the term change order?

A: In all type of construction projects changes are made to be done in construction contract because…

Q: According to CSI, how many formats are there under OmniClass to organize the construction…

A: The objective of the question is to understand the number of formats under OmniClass, their…

Q: I x,0= 10 " I yo = r x,0 = 4"X6"X ½" r yo = 12" 4"X 8"X 1" | 1" 12 "

A:

Q: Describe Design by Contract” principles

A: Design by Contract is a software engineering approach that aims to improve software reliability and…

Q: Give the other name for phase construction?

A: The other name for phased construction is fast track construction. The process involves each work is…

Q: 44. An organization that creates the sets of rules and standards for graphics and document exchange…

A: Reference : Different sets of Standards used for specifications. (Engineering management,…

Q: What is Boundary value testing?

A:

Q: What do you mean by allowances and tolerances in specifications?

A: Tolerance and allowance are two important terms which are used in specifying the dimensions of any…

Q: what does the special design-build documents consist of?

A: The method in which the design and construction services are done considering it as a single unit is…

Q: Provide definition of watste and its types with examples

A: Asked to provide definition of waste and its examples.

Team Management

To complete a specific task or to accomplish organizational goals along with increasing work productivity, individuals need to come together and think along a common path and direction. There are certain tasks in an organization that cannot be done alone and the involvement of more individuals is essential. These groups of individuals who work together for a common goal compose a team and the individual members involved are known as team members.