Assume the following register contents: t0 = 0xAAAAAABA, t1 = 0x82345678For the register values shown above, what is the value of register t2 for the following sequence of instructions?sll t2, t0, 6or t2, t2, t1

The answer to the above problem is given below:-

Answered: sll t2, t0, 6 or t2, t2, t1

Engineering

Electrical Engineering

sll t2, t0, 6 or t2, t2, t1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Write the contents of all registers and the conditions codes registers after each execution instructions in Table Q1(a). Instructions SUBS r0, rl, 12 MOV 12,13, ASR #3 ro 11223344 Table Q1 (a) rl F7770025 12 r3 CF119856 CF119856 NZ V C 010 1
%VY l. In. O Homework1.pdf Q: Compute the physical address for the specified operand in each of the following instructions. The register contents and variable are as follows: (CS)=0A00H, (DS)=OB00H, (SS)=OD0OH, (SI)=OFFOH, (DI)=00BOH, (BP)=00EAH and (IP)=0000H, LIST=00FOH, Ax=4020H, BX=250OH. 1) Destination operand of the instruction MOV LIST (BP+DI], AX 2) Source operand of the instruction MOV CL, (BX+200H] 3) Destination operand of the instruction MOV [DI+6400H], DX 4) Source operand of the instruction MOV AL, [BP+SI-400H] 5) Destination operand of the instruction MOV [DI+SP], AX 6) Source operand of the instruction MOV CL, (SP+200H] 7) Destination operand of the instruction MOV (BX+DI+6400H], CX 8) Source operand of the instruction MOV AL, [BP- 0200H] 9) Destination operand of the instruction MOV (SI), AX 10) Destination operand of the instruction MOV (BX][DI]+0400H,AL 11) Source operand of the instruction MOV AX, [ВР+200H] 12) Source operand of the instruction MOV AL, [SI-0100H]…
draw and identify or explainMake na input circuit using a switch and an external pull-up resistor.What are the logic states of the microcontoller if the switch is open?What are the logic states of the microcontoller if the switch is off?
1What will be the state of a MOD64 counter after 90 input pulses if the starting state=000000?A.100100B.011010C.010110D.011100 2.A MOD 32 counter is holding the count 101112. What will the count be after 31 clock pulses?A.10100B.10010C.10000D.10110
A 4-bit universal shifting register QA, QB, QC and QD and a single serial input called SI, has two inputs so that they determine how to operate, as follows: M0M1 = 00 indicates that it should keep the value of the current outputs, M0M1 = 01 indicates that you should shift right, M0M1 = 10 indicates that you should shift left, and M0M1 = 11 indicates that you should parallel load inputs A, B, C, and D. Design a minimum circuit that implement this record and draw the final schematic diagram. Include the entire design procedure
digital signal processingsignal and systems
Q4) Design a Register File which includes four 2-bit registers (In total, it includes 8 bits). Each register is named as ala0, b1b0, c2c0, d1d0. Registers are loaded from the S input. In addition to that, there are two input signals, X and Y, to determine which register to select (ie. 00 selectsfirst register ala0 etc). Also there is R signal. When W is zero, the content of the register does not change. When the W is 1 the selected register is loaded with a new value by shifting from the S input. Design this register file by using D flip-flops.
This question is from the subject Digital Logic Design. Assume your register number FA19BSExxx (excluding the dashes -) is in Hexadecimal, where xxx are the three digits of your registration number. a) Represent your registration number in the binary. b) Split the ten digits of your registration into two Hexadecimal numbers M and N, where the left most five digits make number M and the right most five digits make number N. Using r’s complement, subtract N from M. In other words, calculate M – N. Solve the question for registration no SP20-BCS-156.
After executing XLAT instruction, the content of system registers is: ES=4E25, DS=041C DI=6814, BX=0201, and AL =40, (all values shown are in hexadecimal and the addresses shown are physical addresses). What is the content of AL before executing this instruction? H. H. Address 20н 40 H 60 н 80 H A0H СОн E0 H Content 447C 447D 447E 447F 4480 4481 4482 Notes: 1- Use the memory fragment shown to answer this question. 2- Write down the final value of AL as two hexadecimal digits without any additional characters.
Electrical Engineering 1. Consider the following MIPS assembly language code: II: ADD Sl, S0, Ss1 LW S0, -4($s1) 13: ADD Sso, Ss0, Ss0 12: 14: SW S0, -4(Ss1) Which of the above instructions will have to be followed by a stall for the correct operation of the processor, given a 5 stage MIPS pipelined processor. 000
1. Write down 2- differences between Von-Neumann and Harvard architecture. 2. you are executing an instruction, SUB $s0, $s1, $s2 (address 0x20). Draw the datapath of this instruction when $s1=10, $s2=5. When are the stages in this datapath? Mark the components which are active in corresponding stages. 3. How to store(1050000)10 in register $s0? Write down the instructions that stores the data in $s0 register.
a) In Assembly programming what is the functionality of the following instructions DECFSZ ВTESC MOVLW MOVWF goto b) A piece of code is required for a time critical activity. Should this be written in assembly language or C? Explain your answer. 5 Explain the difference between the (For) and (While) loops. Highlight the main components of the (For) loop that are required for its execution. Consider the following C program designed to run on a PIC 18F4455. int main(void) 2 { 1 double voltage; double current; double milliwatts; double energyUsed; double cummulativeEnergy = 0; while (1) { voltage=analogRead (VOLTAGE_PIN)*voltageScaleFactor; current=analogRead (CURRENT_PIN)*currentScaleFactor; milliwatts=voltage*current; energyUsed=milliWatts*0.5; cummulativeEnergy=cummulativeEnergy+energyUsed; 10 11 12 13 14 15 _delay_ms (500); 16 } 17 a) What is the role of the symbols "{" and "}" b) The code here is indented. Explain the importance of indentation N m 4 n Or 00 o A m