SITUATION. A soil in its natural state has a moisture content of 30% and a unit weight of 16 kN/m3. The specific gravity of the soil particles is 2.50 Evaluate the void ratio of the soil sample. 0.97 0.677 0.875 0.99

Q: Determine total indeterminacy and external indeterminacy

A: Given data : Number of external support reaction (R)=2+1+2=5Number of member (m)=8Number of joint…

Q: Can you add the datum line in the illustration and make a bettter illustration based on solution

A: Given, Angle made by nozzle = 45o Horizontal distance = 15 to 20 m

Q: Jse commands (rectangle, mirror) and List he commands to draw the following drawing start from a…

A:

Q: Determine external as well as total indeterminacy

A: Given data : Number of External support reaction (R)=2+2=4Number of member (m)=6Number  of joint…

Q: What do you mean by the Bulk Richardson Number (BRN)?

A: The Bulk Richardson Number is defined as the ratio of turbulence due to kinetic energy to the shear.

Q: The ∑ F proceeding in the couple is?

A: Brief concept- Couple- It is a pair of equal and opposite parallel forces. These two forces do not…

Q: Locate the X-X centroidal axis for the cross section shown. £ sym. W840 x 329 W530 × 72 X X

A:

Q: x; ]] a» a» dz || X2 a3 a a33

A: For calculation assume,

Q: AW 12 x 35 steel cantilever beam is subjected to an axial load P = 9.5 kips and a transverse loadv =…

A:

Q: 6 in Gin Gin 9 in 3in

A: Schematic diagram of the given problem:

Q: What is the length of the vertical piece halfway between C and D in feet? B 12'-0" A 16'-0" D 16'-0"…

A:

Q: For the given structures, determine the degree of indeterminacy. 6. T 6

A: The given beam has three support conditions. The Left end is a Fixed support.(3 reactions)…

Q: X 0.75 3 -3.5 1.5 1.5

A:

Q: ETERMINE THE LOCATION OF CENTROIDAL X AND Y. NOTE: UNITS ARE IN INCHES.

A:

Q: XXXX W₂ W₁ Which of the following most nearly gives the external degree of indeterminacy? 2 4 O 1

A:

Q: Determine the XT and YT(using both a and b) a. Using the Top Most, Left Most Reference Line b. Using…

A:

Q: R10 30 50 O. 15 R30

A:

Q: Find the Xp ¢ YT Зст I}1:25 cm Cocn 61.5 cm 0.75 cm

A:

Q: What is the Ix and Iy of the cross-section in mm4

A: Given: Required : Ix and Iy of the cross-section in mm4

Q: aSN 200 mm 350 mm

A: Free Body Diagram (FBD):

Q: Draw the influence lines for the vertical and horizontal reactions, Ax and Ay, at support A and the…

A: Question consist of truss supported at hinge support at A and G . Length of members are given in the…

Q: 643-218

A: Note: As you have nothing mentioned in this problem. So, we are assuming that we have to apply…

Q: ex (x+1)² +c

A: Write all numerators above the common denominatorUse  to expand the expression.

Q: For the given structures, determine the degree of indeterminacy. 1. ♫

A: This question is related to the Structure analysis

Q: 4x-2x2+1 find lim, 3x-5

A:

Q: Find

A:

Q: can you explain how to do this in cad. using the details below. Can you like specify the dimensions…

A: Given data,

Q: Describe Mohr’s Circle.

A: Mohr’s circle is defined as a two-dimensional graph which represents stresses at a point.

Q: 4) A precast T beam with the dimensions shown below is to be a used as a bridge over a small…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: 3. Is Iust be par PROBLEM 1: The frame shown is supported with hinges at A and C and a pin at B.…

A: Both the hinges will have the two supports, they are :- RAx and RAy at A and RCx and RCy at C. Then…

Q: Figure 2. Inside perimeter Outside perimeter Centreline

A: Inside perimeter :Length×2+Breadth×2+2×2'+3'24'3''×2+12'×2+2×2'+3'=79'6''

Q: 100 N 100 N 100 100 150 250

A:

Q: If Ax B = = A.B then the angle between A and B will be %3D a) п b) π/2 ) π/3 TE e) None of the above…

A: To find angle between A and B

Q: Name three lines that intersect at point E.

A: Draw the figure. The lines which meets at the point E is the intersecting lines at point E. The…

Q: Links CF connects members AD and EG. The two vertical links having a rectangular cross-section…

A:

Electronic Spreadsheet

Tabular listing has many advantages ranging from time management to efficient scheduling of tasks. Electronic spreadsheets allow the user to tabulate and analyze data, using its easy-to-use interface. An electronic spreadsheet is a staple application used among accountants, management staff, and IT professionals. It is used in various sectors worldwide for data management. An electronic spreadsheet is a system and computer software that could be used to do numerical computations automatically. Spreadsheet application programs are often organized as a table with rows and columns. Each row and column intersect to form a cell, which may be used to store data. These data can take the form of a written label, a number, or a formula that combines information from other cells.