Situation A. | Six steel cables support a circular moulding of diameter 2 meters. The cables are spaced equally along the perimeter of the moulding. The moulding weighs 2.50 kN/m. Note: Do not round off during calculations, use the store functions of your calculator. 1) If the allowable stress is 124 MPa, determine the minimum diameter of each cable. (mm) 2) If the diameter of the cable is 10mm, determine the vertical displacement of the moulding. (mm)

Situation A. | Six steel cables support a circular moulding of diameter 2 meters. The cables are spaced equally along the perimeter of the moulding. The moulding weighs 2.50 kN/m. Note: Do not round off during calculations, use the store functions of your calculator. 1) If the allowable stress is 124 MPa, determine the minimum diameter of each cable. (mm) 2) If the diameter of the cable is 10mm, determine the vertical displacement of the moulding. (mm)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the height and the following reactions of the cable

A: Given: To find: The height and the support reactions of the cable

Q: P=75KN e=200mm 200 mm 20 mmo 200 mm

Q: Cross section of each bar 350 mm2 . Find stress in bar CD

Q: Three cables having an area of 0.05 in? each is carrying the load W as shown. With no stress, the…

A: Given, A = 0.05 in2 E = 29000 ksi

Q: A 60-inch length of 2-inch OD x 1/8-inch wall 2014-T4 aluminum tube is supported by pinned supports…

Q: s. Determine the tension in each wire.

Q: Q] As shown in figure below, determine the weight of concrete cylinder, for equilibrium the gate AB.…

A: Given- wAB=20kNAssume d=1

Q: Problem 1. The weight of the crate is 580lb. Calculate the force in cables AB and AC. В 3. 30% A

Q: Q1. A homogenous 2000 N bar AB is supported at either end by a cable as shown in figure. Calculate…

Q: Problem 2: A shaft is to be fitted with a flanged coupling having 6 bolts on a circle of diameter…

Q: HE ALL OWABLE SHEAR STRESS FOR ALL PINS IS 1S KSi. ETERMINE THE REQUIRED DIA METER FOR PIN A. 1.0a…

A: Take moment about A :∑ MA=0FBCsin608ft-2882=0FBC=8sin60FBC=9.2376kips'

Q: ll thickness of 10mm and a force of 1500N.

Q: Problem 3.3 - A force F is applied to one end of a cable of length L. The other end of the cable is…

Q: Six steel cables are supporting a circular heavy moulding of diameter 2 m from an overhead point as…

Q: A single strain gauge, placed in outer surface and at an angle of 30 gives a reading at point A of…

Q: steel plate 2.7 m x 1.3 m x 100 mm thick is to be hoisted by a steel cable sling. assume the steel…

A: t=100mm do=18mm

Q: Stability Classify each of the following systems as stable or unstable. If unstable, indicate which…

A: A structure can be stable if the reactions at the supports are not concurrent or not passing from a…

Q: Q| As shown in figure below, determine the weight of concrete cylinder, for equilibrium the gate AB.…

Q: E F 1 m Q2) (25Marks): Determine the deflection in each point of (A,B,C and D) for the steel system…

Q: An 800 N-m couple is applied to the flywheel as shown. The coefficient of belt friction is 0.20. The…

Q: 5. The lap joint shown is fastened by two %-in.- diameter rivets. Calculate the maximum safe load P…

A: (As per student demand, Solution to 5 ) To find:Calculate the maximum safe load P

Q: The yoke-and-rod connection shown is subjected to a tensile force of 5 kN. Determine the average…

Q: A tubular aluminum alloy [G= 4,000 ksi] shaft is being designed to transmit 410 hp at 2,700 rpm. The…

A: Given tubular shaft,

Q: the floor and at A 40 m bar weighing loo N is rerting ot points a srnooth on and against a smooth a…

Q: 1) If the radius of cables AB and CD are 5mm and modulus of elasticity is 20GPA, calculate the…

A: It is asked to find normal stress and normal strain in cable AB & CD.

Q: ugo or your Jolution. - Block B hangs on a cable connected block A through a pulley as shown in the…

Q: Question 37 If the pressure at the circular area is p=150 kPa, calculate the stress increase at…

Q: A horizontal beam AD with cross-section of 3800 mm² is supported by a wire at C and carries a load…

Q: Use the Distortion Energy Failure Theory to assess the adequacy of this pipe. (OD 114 mm; ID 97 mm,…

Q: thickness "t" of the steel plate if the

Q: The uniform square plate is suspended by three equal-length cables as shown. Determine the tension…

Q: Figure 1: 12 kN/m B 100 kN 4 m HNGE m--1.5 m- 5 m

Q: Q1) For the loading shown, determine the stress at (a) point A. (b) point B. В 200 100 F

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: Question 9 From the figure of a cable connection shown. Refer to the details below: Distances: X4.4…

Question

Situation A. | Six steel cables support a circular moulding of diameter 2 meters. The cables are spaced equally
along the perimeter of the moulding. The moulding weighs 2.50 kN/m.
Note: Do not round off during calculations, use the store functions of your calculator.
1) If the allowable stress is 124 MPa, determine the minimum diameter of each cable. (mm)
2) If the diameter of the cable is 10mm, determine the vertical displacement of the moulding. (mm)
W
2.0 m
3.0m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Minimum diameter of the cable for given allowable stress

VIEW

Step 3: Vertical displacement of the moulding for given cable diameter

VIEW

Step 4: Results

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

STRENGTH OF MATERIALS Answer: Maximum tensile 38 MN/m2, maximum compressive 46 MN/m2 Please show the solution to get the answer.
Pls answer, I'll rate. Determine the force in member BD in kN.If the force is compression, enter the answer as negative.Show your complete solution. Thank you so much!
18. A steel loop ABCD of length 1.2 m and of 10-mm diameter is placed as shown around a 24 mm diameter aluminum rod AC. Cables BE and DF, each of 12 mm diameter, are used to apply the load P. Knowing that the ultimate strength of the steel used for the loop and the cables is 400 MPa and that the ultimate strength of the aluminum used for the rod is 220 MPa, determine the largest load P that can be applied if an overall factor of safety of 3 is desired. a. 37.7 KN b. 39.7 KN E С. 74.6 KN d. 45.2 KN B 180 mm 480 mm A 180 mm D
Q3: . A crank built up from cylindrical sections by welding required a loading of 250 lb to overcome the resistance when in the post- tion shown. (a) Compute the maximum normal and shear stresses induced in the section A-A. (b) Determine the maximum shear stresses induced in parts I, II, and III. Ans. (a) (max) = 29,000 psi, T(max) = 15,000 psi (b) 10,550 psi for part I, 6880 psi for II, 15,000 psi for III --A III II 1 Dia. Dia. Fig. 2-38 250 lb 150 "Dia.
kindly please help me answer this question, please be accurate and detailed when it comes to the solution. thank you.
The cable exerts a force of P-6 kN at the end of the 8-m-long crane boom (Figure 1) Figure 1of1 Part A If-30, determine the placement ar of the boom at B so that this force creates a maximum moment about point O Express your answer to three significant figures and include the appropriate units Submit Part B Value (Mo) Request Answer What is this moment? Express your answer to three significant figures and include the appropriate units. Enter positive value of the moment is counterclockwise and negative value if the moment is clockwise. Value Submit Request Answ Units Pearson ? → Ć Units
complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94 What will be the maximum weight of cylinder that can be put as shown in the figure below if the maximum stress at cable is FN mPa? Note: Round off your answer in two decimal places.
pls help! write the solutions completely and legibly. upvote will be given! MECHANICS OF DEFORMABLE BODIES
2 - please provide a clear and complete solution, thanks!
The bucket is being supported be the three cables DA, DB andDC. Note that cables may only carry tension, or the forces are pointing awayfrom point D when analyzed.[1] If the tension in DA is 125 kN, calculate the components.[2] If the tension in DC is 135 kN, calculate the components.[3] If the tension in DB is 80 kN, calculate the components.
Please answer in 1hr thank you