Situation: A conical pendulum has a length of 50 cm. Its bob of mass 100 g performs a uniform circular motion in a horizontal plane in a circle of radius 30 cm. Find the following: The angle made by the string with the vertical. a. 59.04° b. 30.96° The tension in the string. a. 1.23 N The period. a. 1.72 sec b. 1.91 N a. 2.84 b. 1.27 sec The speed of the bob in m/s. b. 2.48 c. 53.13° c. 1.63 N c. 1.42 sec c. 1.94 25 Figure holow shows throp point charges that lie in the x y plano in a yoouum d. 36.87 d. 1.14 N d. 1.10 sec d. 1.49 Find the direction of th

Situation: A conical pendulum has a length of 50 cm. Its bob of mass 100 g performs a uniform circular motion in a horizontal plane in a circle of radius 30 cm. Find the following: The angle made by the string with the vertical. a. 59.04° b. 30.96° The tension in the string. a. 1.23 N The period. a. 1.72 sec b. 1.91 N a. 2.84 b. 1.27 sec The speed of the bob in m/s. b. 2.48 c. 53.13° c. 1.63 N c. 1.42 sec c. 1.94 25 Figure holow shows throp point charges that lie in the x y plano in a yoouum d. 36.87 d. 1.14 N d. 1.10 sec d. 1.49 Find the direction of th

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate for the value and location of the maximum deflection of the simply supported beam shown. 5 kN/m 4m 5m 1m for: E = 200 GPa | = 1865 x 10° mm Moment (EI) equation: [(x – 4)²] [(x – 9)21 +5 M(EI) = 8.75 (x) – 5
В 4m 100kN 5m The structure is composed of bar AB and a semi secular arc as shown in the figure. It is fixed at the lower and a 100 kN load is applied at the free end. Using E = 200 GPa, I =1000x1066 mm4. Calculate the Horizontal displacement of the point where the load is applied. (mm) 19.50 40.01 82.53 45.31 The structure is composed of bar AB and a semi secular arc as shown in the figure. It is fixed at the lower and a 100 kN load is applied at the free end. Using E = 200 GPa, I = 1000x1066 mm4. Calculate the Vertical displacement of the point where the load is applied. (mm) 86.28 46.28 68.42 35.42
Question 1: Referring to Figure 1, use the moment-area method to calculate the end rotations at points A and B (0A, OB) and deflections at points C and D (8c, op). A 5 m P=100KN C P₂=200KN 2.5 m D 2.5 m B
The mechanism for a car window winder is shown in the figure. Here the handle turns the small cog C, which rotates the spur gear S, thereby rotating the fixed-connected lever AB which raises track D in which the window rests. The window is free to slide on the track. If the handle is wound at 0.5 rad/s, determine the speed of points A and E and the speed vw of the window at the instant = 40°. - D 20 mm 0.5 rad/s 50 mm B 0 -200 mm -200 mm A E
Find the magnitude (in Nm) of the couple moment acting on the pipe assembly if P = 56 kN. Round off only on final answer expressed in 3 decimal places.
Paragraf Stiller 2.13: 4 6. 10 11 13.114 15. In Figure 2, the wheel with mass p (kg) with an inertial radius of kA (mrn), M=X.t (N.m) it has been subjected to moment (t seconds). Starting from a stationary state calculate the angular speed of the wheel after t1 seconds. Also, the reaction force that the fixed bearing a exerts on the wheel during movement calculate. (Gravity acceleration will be taken as 9.81 m/s2.) kA= 252 mm p= 13 kg x= 3 t1=2 M DOdak
Example 700 mm An experimental device imparts a force of magni- tude F = 225 N to the front edge of the rim at A w 900 mm simulate the effect of a slam dunk. Determine the moments of the force F about point O and about point B. Finally, locate, from the base at 0, a point C on the ground where the force imparts zero moment. B 300 mm A 3050 mm
BO = 30° 3 m 0 = 45° 2 m D A @AB = 5 rad/s 1. If crank AB is rotating at a constant angular velocity, which body/bodies is/are in general plane motion? Crank AB Crank AB and Rod BD Rod BD Piston D 2. give the closest value of the speed of end B of crank AB? 5.00 rad/s 5.00 m/s 10.00 m/s 15.00 m/s +
Situation 12: 37. 11. A bearn is loaded as shown in the figure. Use E= 200 GPa and 1 = 129x10° mm a. b. B 1 m a. b. 480 N/m 3 m [c 2m Which of the following most nearly gives the rotation at A? 4.20° (counterclockwise) 2 4.02° (clockwise) D 103.16 mm (downward) 94.80 mm (downward) 4.20° (clockwise) b. d.4.02° (counterclockwise) Which of the following most nearly gives the deflection midway between the supports? 2m 600 N d. d. Which of the following most nearly gives the deflection at the overhanging end? 34.88 mm (upward) 56.99 mm (upward) 111.24 mm (downward) 88.45 mm (downward) 56.99 mm (downward) 34.88 mm (downward)
Answer close to 8.55
I would like to know the solution to the given answer. Thank you