Situation 4: The section of a solid concrete beam is shown in the figure. Unit weight of the concrete is 23.5 kN/ m3. fo -3.465 Mpa. The beam is simply supported over a span of 5 m. Consider beam weight. 10. Determine the cracking moment of the beam. 11. If the cracking moment of the beam is 40 kN.m., what is the maximum superimposed uniform load can the beam can carry?

Situation 4: The section of a solid concrete beam is shown in the figure. Unit weight of the concrete is 23.5 kN/ m3. fo -3.465 Mpa. The beam is simply supported over a span of 5 m. Consider beam weight. 10. Determine the cracking moment of the beam. 11. If the cracking moment of the beam is 40 kN.m., what is the maximum superimposed uniform load can the beam can carry?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v=0.33] pipe has an outside diameter of 200 mm, a wall thickness of 5 mm, and a length of 5.4 m. The pipe supports a compressive load of 670 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 6= i AD= i mm mm
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 215 mm, a wall thickness of 12 mm, and a length of 4.3 m. The pipe supports a compressive load of 695 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i AD = i mm mm
Consider the following uniformly loaded simple beam. The beam has a span length L = 2.5 m, the load has a uniform intensity q = 3.8 kN/m, and the maximum bending stress o = 60 MPa. q = 3.8 kN/m L = 2.5 m The cross section of the beam is square, and the material is aluminum having modulus of elasticity E = 70 GPa. (Use the formulas of this example. Use available deflection formulas. All beams have constant flexural rigidity EI.) Calculate the maximum deflection 8, max: (Enter the magnitude in mm.) mm
Prob.5: A rectangular reinforced concrete beam has dimensions b = 300 mm, d = 530 mm and h = 600 mm, and is reinforced with 3 Ø32 mm bars. Materials strength are fe = 28 MPa, fy= 414 MPa. a) Find the moment that will produce the first cracking at the bottom surface of the beam basing your calculations on Ig. b) Determine the maximum stress in the steel and in the concrete under this Design of Reinforced Concrete Structures moment.
A reinforced concrete beam is shown in the figure below. 0.75-in, diameter rods Wo 20 in. 2.5 in. 8 ft- 8 ft 10 in. Part A Determine the maximum uniform distributed load wn that can be supported by the reinforced concrete beam if the allowable tensile stress for the steel is (Ost )allow = 30 ksi and the allowable compressive stress for the concrete is (oconc )allow = 3 ksi . Assume the concrete cannot support a tensile stress. Take Est = 29(10) ksi , Econe = 3.6(103) ksi Express your answer to three significant figures.
The solid circular drill rod AB is made of a steel that is assumed to be elastoplastic with τY = 22 ksi and G = 11.2 × 106 psi. Knowing that a torque T = 72 kip·in. is applied to the rod and then removed, determine the maximum residual shearing stress in the rod. The maximum residual shearing stress in the rod is ksi.
A wood beam is strengthened using two steel plates as shown in the figure below. V 6 mm 150 mm 6 mm |B 100 mm i The beam has simple supports and an overhang and is subjected to a point load and a uniform load as shown in the figure below. 13 KN q= 5.0 kN/m с 3 m Calculate the maximum tensile and compressive stresses of the beam. Assume that E = 11 GPa and E = 200 GPa. (Enter your answers in MPa. Use the deformation sign convention.) maximum tensile stress in wood MPa maximum tensile stress in steel MPa MPa maximum compressive stress in wood maximum compressive stress in steel MPa Need Help? Read It B 000 +1m-
A simply supported wood beam is reinforced with a steel plate of width b as shown in the figure. The beam carries a uniformly distributed load including the weight of the beam) of intensity 279 lb/ft over its 22.3- ft span. Using b = 4 in. and Est/Ewd = 20, determine the maximum bending stress (in psi) in the steel. Round off the final answer to two decimal places. ... 6 in. 10 in. 1/2 in. -b-
Question 6 Before the 400-kN load is applied, the rigid platform rests on two steel bars, each of cross-sectional area 1400 mm?, as shown in the figure. The cross-sectional area of the aluminum bar is 2800 mm?. Compute the stress in the aluminum bar after the 400-kN load is applied. Use E = 200 GPa for steel and E = 70 GPa for aluminum. Neglect the weight of the platform | 400 kN 0.1 mm Steel Aluminum Steel 250 mm
A concrete beam is reinforced by three steel rods placed as shown. The modulus of elasticity is 3* 106 psi for the concrete and 30 *106 psi for the steel. Using an allowable stress of 1350 psi for the concrete and 20 ksi for the steel, determine the largest permissible positive bending moment in the beam.
The reinforced concrete beam shown is subjected to a positive bending moment of 178 kN-m. Knowing that the modulus of elasticity is 25 GPa for the concrete and 200 GPa for the steel, determine the stress in the steel and the maximum stress in the concrete. 540 mm -350 mm The stress in the steel is The stress in the concrete is 25-mm diameter 60 mm ↑ MPa. MPa.
The composite shaft shown in the figure consists of a bronze sleeve (1) securely bonded to an inner steel core (2). The bronze sleeve has an outside diameter of 40 mm, an inside diameter of 30 mm, and a shear modulus of G1 = 44 GPa. The solid steel core has a diameter of 30 mm and a shear modulus of G2 = 84 GPa. Assume L = 360 mm. The composite shaft is subjected to a torque of T= 820 N-m. Determine (a) the maximum shear stresses in the bronze sleeve and the steel core. (b) the rotation angle of end B relative to end A. A T T (1) B Answers: (a) T1 = MPа MPa 72 = (b) PBIA = rad (2)