SITUATION 3: A homogenous ladder 10m long and weighing 3.5 kg/m leans against a vertical wall. The angle between it and the floor is 60 degrees. The coefficient of friction of the ladder against the ground as well as the wall is 0.35. 6. How far up the ladder measured from the ground can a 65-kg man climb before it starts to slide? а. 4.5 m c. 5.4 m b. 6.3 m d. 7.3 m 7. Compute the reaction at the wall when it starts to slide, in N. а. 324.07 C. 410.32 b. 390.15 d. 107.06

SITUATION 3: A homogenous ladder 10m long and weighing 3.5 kg/m leans against a vertical wall. The angle between it and the floor is 60 degrees. The coefficient of friction of the ladder against the ground as well as the wall is 0.35. 6. How far up the ladder measured from the ground can a 65-kg man climb before it starts to slide? а. 4.5 m c. 5.4 m b. 6.3 m d. 7.3 m 7. Compute the reaction at the wall when it starts to slide, in N. а. 324.07 C. 410.32 b. 390.15 d. 107.06

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A crate of 400 lb is resting on a rough horizontal surface having a coefficient of friction of 0.40.Determine the force P required to cause a motion to impend if applied to the crate on thefollowing listed below.a. Horizontallyb. Downward at 30° with the horizontal
Determine the tension T in the belt needed to overcome the tension of 200 lb created on the other side. Also, what are the normal and frictional components of force developed on the collar bushing? The coefficient ofstatic friction is μs = 0.21.
Question 3 The roof system consists of 130 mm thick reinforced concrete slab ( density = 23.6 kN/m²) resting on steel beams (A=15000 mm²) which are supported by steel girders (A= 40000 mm²). Density of steel is 77.3 kN/m³. Determine the magnitude of the axial force acting on column A. Answer in kN rounded-off to 2 decimal places. CO a = 7.5 meters b = 3.1 meters 5144Hz B 3 at beach Steel column 130 mm concrete S16
What is the equivalent static force (in kips) if pseudo-acceleration is 2.34g and the weight of the vibrating structure is 75 kips?
A person on horseback is on a drawbridge which is at an angle 9 = 20.0° above the horizontal, as shown in the figure. The center of mass of the person-horse system is d = 1.00 m from the end of the bridge. The bridge is = 6.99 m long and has a mass of 1,920 kg. A cable is attached to the bridge 5.00 m from the hinge and to a point on the wall h = 12.0 m above the bridge. The mass of person plus horse is 1,260 kg. Assume the bridge is uniform. Note that the drawing is not to scale and you may not assume that the cable is perpendicular to the bridge. (Due to the nature of this problem, do not use rounded intermediate values in your calculations-including answers submitted in WebAssign.) (a) Determine the tension in the cable (in N). 20623 X Draw a diagram of the bridge, with forces and distances clearly labeled. Use your diagram to write the torque equation for rotational equilibrium with rotation axis at the hinge, and solve your equation for T. N (b) Determine the horizontal force…
, shown below is being hoisted up with the force 1. The cylinder of weight, W= 380 kN F against the vertical wall. If us = 0.57 Ms W Ms a. Determine the reaction force (resultant of normal force and frictional force) against the vertical wall. b. Calculate the force, F, needed to set the cylindrical roller in motion.
A steel beam, of lengths a = 6 m and b = 3 m and a hollow box cross section, is supported by a hinge support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300 mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of the intensity that linearly varies from q=0 kN/m to q = 3.1 kN/m for AB span; and is constant with q = 3.1 kN/m for BC span. The Young's modulus of steel is 200 GPa. A y, v a 5 mm 200 mm Figure Q.1 9 A B 300 mm b C X
Fluid Mechanics The buoy is at 1.5m diameter and weighs 3.8kN. I need the detailed solutions and detailed drawings, thanks!
1. The magnitude of the bending moment acting on the circular cross section of a beam is M = 30 000 Ib - ft. Calculate the bending stresses at the following points on the cross section: (a) A; (b) B; and (c) D. 60°- B. 6 in. 8 in.
A steel beam, of lengths a= 6 m and b= 3 m and a hollow box cross section, is supported by a hinge support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300 mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of the intensity that linearly varies from q = 0 kN/m to q = 3.1 kN/m for AB span; and is constant with q= 3.1 kN/m for BC span. The Young's modulus of steel is 200 GPa. Part A Calculate: A y, v a 5 mm 200 mm Figure Q.1 9 S B 300 mm b с X
A segment of an electric power transmission line with supports at the same elevation is shown in Fig. A horizontal force of 3000 Ib was applied to the line before it was attached to the towers. The weight of the line is 1.5 lb/ft. Determine The sag at the middle of the span.
Situation 4: An open horizontal tank 2 m high, 2m wide and 4mlong is full of water. Determine the amount of water spilled out when the tank is accelerated horizontally at 2.45 m/s in a direction parallel with its longest side in m?. Find the force acting on the side with the greatest depth in kN. 9. 10.